Hi Silly question - How do I open the .ctz file.
Its been over 12 years on the PT.net forum - seen quite a few mods! And you?
Thanks
Type: Posts; User: jamesbond2509; Keyword(s):
Hi Silly question - How do I open the .ctz file.
Its been over 12 years on the PT.net forum - seen quite a few mods! And you?
Thanks
I need to run my MAF tune for a day and then flash it back to speed density!
Okay so here is the tune that I need to have the P0102 colds not showing. It is a Speed density tune using a custom operating system. I went back to plug in the MAF and it is idling really rough...
Actually I read your earlier post - Looks like I have to run this in MAF/mode temporarily - except I cannot get this thing to idle in this mode??
Hi Joecar - Thank you very much for your reply - So if I connect the MAF and reset the code I can continue to run SD and the MAF Error will go away?
Best Regards,
I'm currently running Speed density on a 2002 GMC with a 6.0 engine with that custom operating system. I'm trying to get rid of the PO 102: but I understand the MAF has to fail for speed density to...
Hi John, the tables were good as starting point - eventually I have to add a 20% factor to ensure I didn't go lean in the Boosted. The timing table worked out well - Thanks again.
PS is this...
Im finding that after some tuning in closed loop light to mid throttle, the AFR fluctuates between 14.3 & 15.3. Can anyone confirm if this is normal for closed loop operation. Im thinking that If I...
Yes it worked! The MAF tables were still there, I had to bring the MAF frequency diagnostics back to stock. My tune was kind of upset but did not throw any codes. Cheers
Hi John Thanks again, at least it is a starting point. I have to get emissions first then I'll try this as a starting point for tuning.
Best Regards
OK Ill give it a shot an report back! Thanks
Joe if I put a MAF back in then the DTC will go away - so will I need to do anything to the SD tune to run the MAF. I followed all the efilive instructions to go to Speed Density.
Hi John, Thanks a lot, appreciate your help very much. I'm going to try it and report back. I was also wondering if I could have a look at your VE tables since I just changed over to a turbo and...
I need the DTC to go away for the SRT any thoughts?
Im currently running Speed Density and have the p0102 code - I was wondering how to make this DTC code go away. Any thoughts?
Interesting, I always thought for the return fuel system with the FPR you need to adjust B4001 to account for the pressure various manifold vacuum pressures.
And yes I always get p0102 - is there...
I find from observation that the turbo seems to spool very well at 25-30 degrees of timing until I hit boost. Anyone able to post their timing tables?
Hi JC I have made some changes and have some comments to you recommendations, please advise. Thanks
B3618: need to this to EQR 1.25 for boost (i.e. when MAP exceeds B3613 which you have set to...
Yeah it is my current tune, however previously used for a blower and it is speed density. I usually run 94 octane and have not had any problems with knock. I will try lowering the WOT timing - It is...
I recently installed a T7675 on my 6.0 litre and am trying to tune for a good spool. It looks like timing in the 30 degree range helps spool the turbo faster. Can someone look at my tune and make...
Folks!
It has been a while since I've been on this site. I've recently removed my blower and have installed A turbonetics T7675 Im having some trouble idle tuning in gear. When ever im in gear...
Ross,
Im trying to tune my ls9 cam in my lq4 - Im wondering if I can use the same high octane table - it sure looks different but im intrigued by thinking that the high LSA may require more...
I did not mess wit hany startup tables - however I have been changing the ve while cranking and brought the idle flareup on startup way down and that seems to help
Joecar, Is there anything in my VE table which you see as not optumized. Please advise.
Thanks
My VE table seems to be optumized - and I went through all the idle tuning tutorial - was wondering if there's anything else that could be done. Something happens when I reflash the pcm and those...