Search:

Type: Posts; User: RD TRCTR; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    48
    Views
    29,376

    OK, I am listening. Thank you for the...

    OK, I am listening. Thank you for the information.

    biggy and I have been discussing this exact topic on another forum as we are both having this issue.

    So.. the issue that exists cannot be...
  2. Replies
    4
    Views
    2,844

    24346

    24346
  3. Replies
    21
    Views
    7,590

    Wow, posting this file is a bit dangerous...

    Wow, posting this file is a bit dangerous...
  4. Replies
    6
    Views
    2,400

    Is the posted stock file for the 2012 "correct"...

    Is the posted stock file for the 2012 "correct" for a 2010, no. Can it be used, yes. I am not saying that it is correct. I have had multiple CM2200 trucks show up running quite happily on a...
  5. Replies
    3
    Views
    1,593

    The numbers on the ECM is what the truck left the...

    The numbers on the ECM is what the truck left the factory with.

    Use V8, go to OBD and then do a read, that will show you what is currently on the ECM.
  6. Replies
    2
    Views
    1,246

    For a stock engine with all components, you need...

    For a stock engine with all components, you need a stock file for your 2013.

    If you have items missing to the point that your truck is offroad use only, you can use the 2014 file on the 2013.
  7. Replies
    1
    Views
    1,167

    Check the other thread that you posted to

    Check the other thread that you posted to
  8. 24107

    24107
  9. Replies
    0
    Views
    886

    Early 6.7, CM2100 Equivalency Ratio

    Is is possible to have Equivalency Ratio added to the early 6.7, CM2100 ECM files? Or to receive a .cax file?

    The CM849, CM2200, CM2350 and CM2450 all have it mapped.
  10. Replies
    1
    Views
    1,575

    Changing the actuator doesn't typically resolve...

    Changing the actuator doesn't typically resolve the issue as the turbo is shot.

    I have never run a turbo off file with the VGT in place, sounds like a terrible idea.
  11. Replies
    4
    Views
    3,490

    Yep, I ended up figuring out it. Took an...

    Yep, I ended up figuring out it. Took an extensive amount of googling.
  12. Thread: DSP5 question

    by RD TRCTR
    Replies
    1
    Views
    2,081

    Yes, you can splice a new switch into an...

    Yes, you can splice a new switch into an existing. Disconnect the batteries, the the wires from the current switch one at a time, then splice the new wires/ switch in.

    Buy a switch specific to...
  13. Replies
    5
    Views
    2,322

    Manual or auto truck?

    Manual or auto truck?
  14. Replies
    6
    Views
    2,982

    I think what you're referring to is used to...

    I think what you're referring to is used to calculate the N/V load. The speedometer is controlled by the BCM module in the 13 and newer trucks.

    AlfaOBD or a HyperTech tire calibrator is what I...
  15. Thread: CM2350 Modes

    by RD TRCTR
    Replies
    7
    Views
    3,305

    The OP is referring to a CSP4 file. At least in...

    The OP is referring to a CSP4 file. At least in the 13 and newer trucks, each CSP "tune" has Base, Mode 1 and Mode 2 with the rest of the modes outside of the CSP area.
  16. Replies
    4
    Views
    3,490

    LMM rail pressure issue

    Has anyone ever had an issue getting an LMM to command more than 180 MPa rail pressure?

    I have set the cal to 200, and the commanded rail pressure will never go above 180.
  17. Thread: tune help

    by RD TRCTR
    Replies
    3
    Views
    2,299

    It's easy math, if 2300 microseconds equals 325...

    It's easy math, if 2300 microseconds equals 325 horsepower, determine the microsecond to hp ratio and then divide the on time in tune 5 by the ratio. If rail pressure is raised, 1% increase in rail...
  18. Replies
    2
    Views
    1,604

    Nice first post, thanks for the proper grammar. ...

    Nice first post, thanks for the proper grammar.

    Throw the RaceMe in the trash where it belongs.

    Do you have an EFILive V2? Yes, the message that you would like gone can be disabled. If you're...
  19. Replies
    3
    Views
    2,339

    Contact Starlite or Ridge Runner, they may be...

    Contact Starlite or Ridge Runner, they may be willing to sell you a stock, base file.
  20. Replies
    3
    Views
    4,355

    Thank you for the reply Ross. Unfortunately...

    Thank you for the reply Ross.

    Unfortunately that doesn't really answer my question. I understand that known, good base files are kept in the above mentioned link. I have all of them saved.
    ...
  21. Replies
    3
    Views
    4,355

    CM2350 "recovery files"

    I have a truck that was tuned via another platform. The guy wasn't happy with the customer service and that his phone always struggled to connect to the device.

    I flashed the exact tune from one...
  22. Replies
    2
    Views
    1,645

    Injector balance rates are not able to be...

    Injector balance rates are not able to be "scanned" with EFILive. You're best off to use a SnapOn Solus Edge.

    The issue you're experiencing is probably cold start. Record Main Injection time,...
  23. Replies
    5
    Views
    2,485

    There are two scenarios here... 1. Cold...

    There are two scenarios here...

    1. Cold weather warm up, exhaust brake functionality at idle. It's a bit and is ECT dependent.

    2. Exhaust brake function enable latch, which is for the exhaust...
  24. Replies
    9
    Views
    4,142

    Thanks again!

    Thanks again!
  25. Replies
    9
    Views
    4,142

    Thank you Ross! For a CSP4 file, can I just...

    Thank you Ross!

    For a CSP4 file, can I just copy the 32150200.calz file and rename it 52150200.calz? Or does the file content need to be multiplied as well?
Results 1 to 25 of 52
Page 1 of 3 1 2 3