Search:

Type: Posts; User: Dragframe; Keyword(s):

Search: Search took 0.00 seconds.

  1. Sticky: Posting a response so the next guy with the same...

    Posting a response so the next guy with the same issue figures it out.

    b1703 is what table needed to be adjusted to allow it to idle without the maf. It had a really low number like 60 in the...
  2. What I meant is in the latest efi live update,...

    What I meant is in the latest efi live update, they changed some security stuff and older versions of the software wont open files from the latest software.

    BTW. I figured out my idle issue was...
  3. I have the same setting on b5145. B5114 I have...

    I have the same setting on b5145.
    B5114 I have pulling timing at 2400 as im on the button at 2500 with a window switch.

    When i tried it with the window switch activating the e85 mode... it took...
  4. Well since this forum is dead and support is non...

    Well since this forum is dead and support is non existent from the community or anyone for that matter with EFILive... i figure i should report back for the next guy trying this..

    Unlike the...
  5. E38 COS being used for nitrous and a couple quick questions.

    So I loaded up the COS and populated all the required tables. Pinned a wire into the pcm and tested it to verify it detects ethanol in the system when 12v applied.

    My question is can i use my...
  6. Hmm latest update locked older versions from...

    Hmm latest update locked older versions from opening its tune files. Ever since HPT and EFILive started deleting epa tables off i dont want to update lol
  7. Yeah that maf fail issue haunted me. I made a big...

    Yeah that maf fail issue haunted me. I made a big change i need to test to see if it will idle now with the mad failed though. I report back to ya when i get around to failing the maf again. Right...
  8. Sticky: I did hange the gear ratio in both the ecm/tcm. I...

    I did hange the gear ratio in both the ecm/tcm. I didnt change the wheels/tires on the truck so i didnt mess with that. Though it does have some really freaking strange numbers in there for the tire...
  9. Sticky: its a 2007 4.8 with the Cam listed in OP... ls6...

    its a 2007 4.8 with the Cam listed in OP... ls6 valve springs. 1 7/8 long tubes.. 3" Y pipe.. full 3" exhaust with open style muffler... 3200 stall converter... 4.56 gears.. and nitrous.

    I put on...
  10. Sticky: So what would cause low vacuum when on MAF only?...

    So what would cause low vacuum when on MAF only? Finding that with running maf only (no other changes), im dealing with vacuum/brake issues that i hadn't run into before. I have read a lot of guys...
  11. Sticky: I enabled the maf from 500rpm up and the wideband...

    I enabled the maf from 500rpm up and the wideband seems to hold a more stable afr. Idle is a bit strange running maf only. Hard to describe. But it seems to drive well overall. Also seems to go into...
  12. Sticky: So its a no go. Truck wont idle. Throws a p0103...

    So its a no go. Truck wont idle. Throws a p0103 code like one would expect. Same symptoms I describe above. Just doesn't even attempt to hold the set idle speeds. If i'm not holding the throttle...
  13. Sticky: Thank you. I'm Nashville till Saturday so ill...

    Thank you. I'm Nashville till Saturday so ill load er up on the truck when i get back! Illl report back then. Though your changes look pretty similar to that which i already tried.

    Would you like...
  14. Sticky: Yes sir I can albeit a bit reluctant due to...

    Yes sir I can albeit a bit reluctant due to embarrassment lol

    I had a turbo car i built when i was 19 back in 07-08... Put a SD operating system on it and tuned the car easily. Car is still...
  15. Sticky: Have tried this with no luck unfortunately. Im...

    Have tried this with no luck unfortunately. Im nearly positive it is not referencing the idle tables.
  16. Sticky: It uses the high octane spark table rather than...

    It uses the high octane spark table rather than the idle spark. B1829, B1821, b1651, b1652, all what seems like all the idle tables are not referenced Whatsoever. You can change the values to...
  17. Sticky: Interesting Issue: MAF failure = Idle tables ignored. Cant tune VE because of it

    So im working on my 2007 Silverado with a 4.8 and ran into something interesting.

    I put a 224/230 .553/.546 111+2 Cam, bolt ons, stall, various stuff in the last week.


    What i found is when i...
  18. Thank you! Been lurking here and there for awhile...

    Thank you! Been lurking here and there for awhile now.

    I haven't had a wbo2 since the turbo car. Haven't had a need for one.

    I 'm having a buddy dig his up so I can use it to see if there is a...
  19. Newb tuner. Old ls1 car with my newb tune walked my new stock Ls1

    Quick background on me. 23 years old and my first tuning project was my 96 t/a with a lm7 swap with a 70mm and a 2 bar efi live tune done totally by myself. Was quick and dirty but safe and ran well....
  20. Thread: Knock at WOT

    by Dragframe
    Replies
    17
    Views
    9,659

    wow didn't know the stock stuff was that off!

    wow didn't know the stock stuff was that off!
Results 1 to 20 of 22