Search:

Type: Posts; User: ChipsByAl; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    350

    What kind of vehicle is it?

    What kind of vehicle is it?
  2. Sticky: It runs windows 7 Pro Al

    It runs windows 7 Pro
    Al
  3. Sticky: Hi Paul, my last update was from October 2018...

    Hi Paul, my last update was from October 2018 (Version 7.5.24), been a while. Anyway thanks for the "tun" file fix. My problem has been closing the program. If I use the "X" in the top right corner I...
  4. Replies
    3
    Views
    444

    Its not the km/H causing you the problems, its...

    Its not the km/H causing you the problems, its because the reluctor tooth count is incorrect. Check the speedo section of the donor OS file and you will see that H0102 is 40 and yours is at 17....
  5. Manual or auto? You can also try here:...

    Manual or auto? You can also try here: https://www.dropbox.com/sh/4ydh5wltk3ssxbw/AABfLhrwk_9cnvNKa9pcXuoea/Corvette?dl=0&subfolder_nav_tracking=1
    Al
  6. Interesting project, Ponrov. What vehicle did the...

    Interesting project, Ponrov. What vehicle did the harness come from? Or did someone build it for you? Is there a 4L60 to 4L80 adapter getting used?
    Al
  7. Replies
    2
    Views
    256

    You might need to change units on the device....

    You might need to change units on the device. Look at page 31 in the manual.
    Al

    PS. I don't have one of these, I just looked at the manual....
  8. Replies
    11
    Views
    788

    Thanks for sharing. Al

    Thanks for sharing.
    Al
  9. Well you know what will work for sure! Nowadays...

    Well you know what will work for sure! Nowadays harnesses can have subtle differences that need to be checked pin for pin. Since you have the adapter, that's the way I would go.
    Al
  10. Replies
    6
    Views
    531

    Keep the MAF if you can and put the stock MAP...

    Keep the MAF if you can and put the stock MAP sensor with a good grommet in the hole where the MAP sensor goes. That will get you in a better place to start tuning. There are tutorials here on the...
  11. Replies
    6
    Views
    531

    I'm not sure of the design of the intake...

    I'm not sure of the design of the intake manifold, but I would strongly recommend against running a 3-bar sensor on a normally aspirated engine. You will lose 2/3 of the VE table resolution. You...
  12. Replies
    6
    Views
    531

    Did you change the map sensor because you are...

    Did you change the map sensor because you are planning on using boost? If so it would be best to convert to the later model PCM.
    Al
  13. Replies
    6
    Views
    699

    Glad you got it sorted. It’s a shame that...

    Glad you got it sorted. It’s a shame that sometimes the aftermarket doesn’t pay attention to details like that.
    Al
  14. Replies
    6
    Views
    699

    Is the rotor correctly orientated? You need to...

    Is the rotor correctly orientated? You need to check the plastic pins on the bottom of it, making sure they line up with the pins in the shaft. If the rotor can go on either direction, (not sure...
  15. Replies
    16
    Views
    2,197

    Try to get your tuner to post the file that he is...

    Try to get your tuner to post the file that he is using.
    Al
  16. Replies
    16
    Views
    2,197

    So you probably don't have a correct crank...

    So you probably don't have a correct crank signal, incorrect software in the PCM or bad PCM. You definitely have something coming out of the crank sensor and wiring. Can you use the scan tool and...
  17. Replies
    16
    Views
    2,197

    Fuzzman sorry I could not get to you sooner, been...

    Fuzzman sorry I could not get to you sooner, been busy. Your first post has a few points I need to go over to be sure we are on the same page.

    You have a "beautiful, square signal on the scanner"...
  18. Replies
    16
    Views
    2,197

    The PCM does not have to be out of a van. Any one...

    The PCM does not have to be out of a van. Any one with the correct part #'s including the 9354896 can be used. The software including the Operating system and the Calibrations are more specific. Can...
  19. Replies
    2
    Views
    871

    This may work for you. It is not a DBC file...

    This may work for you. It is not a DBC file though.
    Al
  20. You may want to disconnect the pipe to the evap...

    You may want to disconnect the pipe to the evap purge valve and cap the valve and pipe. If the evap system attempts to purge the canister and it is oversaturated with fuel, the purge valve will draw...
  21. Replies
    63
    Views
    55,972

    https://forum.efilive.com/showthread.php?15236-Cal...

    https://forum.efilive.com/showthread.php?15236-Calc-VET-correcting-MAF-and-calculating-VE-(in-single-log)

    This is his work. You can start here. There is good info in this thread.
    Al
  22. Ryan you can go to GM's site and check your VIN...

    Ryan you can go to GM's site and check your VIN at https://tis2web.service.gm.com/tis2web
    You will need to pick PCM/VCM from the drop down list and then select "Complete History" There you will be...
  23. I don't have a 5.3 file that you can compare to...

    I don't have a 5.3 file that you can compare to or use directly. The current OS for this ECM has updated. It may be safe to just upload another similar OS tun file to see if you can get it running....
  24. Replies
    14
    Views
    1,770

    Did you try using a pull up resistor in the...

    Did you try using a pull up resistor in the circuit ? Not sure if is necessary or not.
    Al
  25. Replies
    41
    Views
    4,771

    Joe watch the "decimal reference" they are not...

    Joe watch the "decimal reference" they are not decimals on the Hex side. They are 0D and 0A or "Zero D and Zero A"

    21684

    Thanks for the help guys.
    Al
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4