Search:

Type: Posts; User: Mr teabags; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    1,458

    I figured it out with a little reading on this...

    I figured it out with a little reading on this forum all is good i managed to full flash new tcm with my old tcm op system car seems to be running now with no codes , thanks for help
  2. Replies
    4
    Views
    890

    ok , i just enabled and full flashed tcu with...

    ok , i just enabled and full flashed tcu with files all good car drives , no more fault codes , thanks .
  3. Replies
    4
    Views
    890

    sorry new to this , I meant operating system...

    sorry new to this , I meant operating system checksum disabled.
    here is the file thanks.
  4. Replies
    4
    Views
    890

    programming T42 controller help please

    hi im new to this , have the v2 and been trying to re program a new unit with the old units data and
    when i compare both tunes for differences i get 24231674 operating system N/A checksums are...
  5. Replies
    13
    Views
    1,458

    i think i have managed to extract data from...

    i think i have managed to extract data from damaged t42 tcm


    new tcm t42 data current if some one can compare the two would be great help
  6. Replies
    13
    Views
    1,458

    sorry for mis information . the codes i am...

    sorry for mis information . the codes i am getting are from engine on an then P will stay on dash until codes cleared .237182371923720237212372223723


    23723

    this is what i could extract...
  7. Replies
    13
    Views
    1,458

    sorry , my combo has been running good for about...

    sorry , my combo has been running good for about six years , it is an 05 model which we were running the t42 tcm with a PCS controller pigy backed of the original TCM to run the 4l80E . The original...
  8. Replies
    13
    Views
    1,458

    The TCM has been linked with other modules and...

    The TCM has been linked with other modules and correct vin in new TCM has been installed the dealer checked the OS in new TCM and assures all is correct and up to date . He told me that it is an...
  9. Replies
    13
    Views
    1,458

    Thanks for the reply . I have linked an exchanged...

    Thanks for the reply . I have linked an exchanged unit and now the module shows up present but the issue im having is still present which when acc is on i do see all gear selection on vehicle dash...
  10. Replies
    13
    Views
    1,458

    T42 TCM read and write

    Hi , I have a flashscan v2 and am having comms issues with a faulty t42 tcm . Is it possible to extracts the op system and transfer the data into a purchased second hand unit .
  11. Hi Eric , I just understood what this response...

    Hi Eric , I just understood what this response meant. I now have more reading to absorb, obviously with an over-temp brain.:book:
  12. Replies
    6
    Views
    1,457

    Sorry guys the sandisk 16gb memory card works well

    Sorry guys the sandisk 16gb memory card works well
  13. Thanks , again .

    Thanks , again .
  14. I think I found it and put it in my calc_pids as...

    I think I found it and put it in my calc_pids as such. Not sure if correct method but when you add text do you
    add to the one file ?
  15. Hi Joe , I am slowly understanding this tunning (...

    Hi Joe , I am slowly understanding this tunning ( efilive ) as I progress and hopefully understand I become more excited. I am still
    waiting for my plx W/B serial conversion with the TTL converter...
  16. 32 views no help:Eyecrazy:

    32 views no help:Eyecrazy:
  17. Hi Erik, thanks for the response . I am very new...

    Hi Erik, thanks for the response . I am very new to efi -live slowly learning through the forum and hopefully understanding enough
    to have the confidence in applying what I learn to my own...
  18. Tried everything scan v7.5 fuel pids will not validate

    hi , tried everything right click for more info but cannot validate gm.ibpw1,gm.ibpw2, e40ecm am I missing something
    attached pid list
  19. Replies
    6
    Views
    1,457

    All sorted , the sd card I purchased was not...

    All sorted , the sd card I purchased was not compatible, replaced all good
  20. Replies
    6
    Views
    1,457

    V2 Goes Blank When I Load A SD Card

    Hi , Im following the tutorial on installing a SD card but the V2 Unit Looses power On lcd screen and I loose
    communication . If I remove the sd card it will power back up . SD card im using is 16gb...
  21. Joe , in my user config folder I have two...

    Joe , in my user config folder I have two calc_pids.txt documents . I may of copied one from the forum and placed it in my folder .With
    the calc_pids.txt e40 file. Do you only need the one and make...
  22. did a log and believe it logs the sae. lambda...

    did a log and believe it logs the sae. lambda which is the EQ ratio . this log was mostly at idle. im using the laptop and
    V2 . Also when you log through BBL how do you look at the log with V7.5...
  23. Hi Joe , im trying to validate my pids (22) of...

    Hi Joe , im trying to validate my pids (22) of them but the GM.EQIVRATIO,GM.IBPW1,GM.IBPW2,AND GM.DYNCYLAIR PIDS WILL NOT VALIDATE they have an x next to them ?
  24. Hi joe , I want to use the sae.lambda and...

    Hi joe , I want to use the sae.lambda and EXT.w02lambda1 pid but I don't see the CALC. ben pid for lambda ?
  25. Tuning CUSTOM E40 ECM boost VE table with lesser injectors!

    Hi, very new to efilive, have purchased the v2 unit and have been reading the forum pro furiously
    Months now .Trying to gain enough exp and knowledge to make my own adjustments :Eyecrazy. My tune ...
Results 1 to 25 of 27
Page 1 of 2 1 2