Search:

Type: Posts; User: Harrismarine; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    304

    Absolutely but its a custom setup in a boat so...

    Absolutely but its a custom setup in a boat so the client has never run the factory car tune, I will be tuning it once its running (remotely) so I was just checking that its a reasonable start up...
  2. Replies
    3
    Views
    304

    Anyone?

    Anyone?
  3. Replies
    3
    Views
    304

    E38 Mafless

    Hi everyone, Is it possible for someone to check this before i send it to a client as a start up tune. I just want to make sure I haven't missed something as I don't use the E38 that much

    Many...
  4. Awesome thanks guys

    Awesome thanks guys
  5. Cell tracking between V8 Tune file and V8 Scan

    I am transitioning over to V8 and cannot seem to get cell tracking in the tune file when reviewing a scan file. eg main VE table is not tracking the cells that the scan file shows. Using LS1 files,...
  6. Replies
    0
    Views
    1,839

    Autocal V3 and innovate MTX-L wideband

    Hi All, Can someone tell me which wire goes to where from the out wiring on the the MTX-L ( red, Black, Blue, white) To the 3 pins on the connector that goes into the AutoCal V3? I think I have...
  7. Replies
    1
    Views
    572

    512 ECM tune into a 1meg ECM

    Can I flash a base tune from a 512 LS1 ECM into a 1meg LS1 ECM? (after flashing a custom operating system into the 1meg)
  8. Thread: Ls1 pcm

    by Harrismarine
    Replies
    4
    Views
    1,098

    Perfect thanks

    Perfect thanks
  9. Thread: Ls1 pcm

    by Harrismarine
    Replies
    4
    Views
    1,098

    Ls1 pcm

    I use allot of 411 (blue/red connector) as we almost always use cable throttle. I know some use the PCM with blue/green connectors with cable throttle. Is there particular blue/green ones that can...
  10. Replies
    3
    Views
    4,988

    Link Autocal

    I am new to autocal can someone point me to the link and unlink instructions I have searched but cannot find the info. I have it all set up and it logs data no problem i just want to link it to my...
  11. Replies
    6
    Views
    3,348

    Yes wide band powered up. I went through it again...

    Yes wide band powered up. I went through it again as you have listed ( I had it correct) and it still shows not found
  12. Replies
    6
    Views
    3,348

    That's what i thought..all i get is "WO2 not...

    That's what i thought..all i get is "WO2 not found" I am betting i haven't got something right. any suggestions?
  13. Replies
    6
    Views
    3,348

    Thanks, so if i have it powered with USB and go...

    Thanks, so if i have it powered with USB and go to Display W02 it should show up? (wide band connected and powered up as usual)
  14. Replies
    6
    Views
    3,348

    Wide Band viewing on V2

    Hi Guys, Can i use my V2 as a gauge to view the wide band when powered up but not connected to a ECU (wide band is connected via serial) basically use it as a gauge?

    Cheers Mike
  15. Replies
    0
    Views
    1,062

    Spark plugs

    Hi guys, I have converted my Big block Chev in my sea boat to injection, I converted the distributor to 2X LS cam wheel with LS3 cam sensor and fitted 24X reluctor to the front of the crank with LS1...
  16. Replies
    3
    Views
    1,877

    Thanks for the replies I'll look into V4

    Thanks for the replies I'll look into V4
  17. Replies
    3
    Views
    1,877

    VN-VR Commorore 3.8 V6

    I would like to have a play with the computers for the above engines for boat application. Can someone advise me as to which softwhare I would need and where to get it from, Merry Christchmas all...
  18. Replies
    2
    Views
    1,468

    can I log in lambda

    We are running up a race motor on 100% methanol, can I log in lambda instead of afr?



    Never mind a closer look sorted it..
  19. Replies
    4
    Views
    2,163

    Its taking timing out

    Its taking timing out
  20. Replies
    4
    Views
    2,163

    I think I may have found two issues, A faulty...

    I think I may have found two issues, A faulty knock sensor and something going on when going into PE. the thing is that same tune on another motor is not doing it
  21. Replies
    4
    Views
    2,163

    Problem with knock

    Hi guys I have a L98 with LS1B computer that I am giving a retune but at 4000rpm it removes 6 deg of timing (I know its not knocking) even if I zero every knock table it still does it...any...
  22. Replies
    4
    Views
    3,843

    So full flash the program that allows oil...

    So full flash the program that allows oil pressure and put in calibration should work?
  23. Replies
    4
    Views
    3,843

    RR and oil pressure

    Is there a reason my RR will not log oil pressure, when I go to the vehicle computer it logs it OK (LS1)
  24. Replies
    19
    Views
    10,067

    I think I see where I have been getting...

    I think I see where I have been getting confused...when you read V2 you still need to highlight the pid list you need to view, I thought it would automatically open the one I had just saved
  25. Replies
    19
    Views
    10,067

    Thanks thats what I thought. I have selected the...

    Thanks thats what I thought. I have selected the pids that i want and programed them into V2 but when I go to read from v2 the pid selection is changed is that correct?

    Is there a reason that...
Results 1 to 25 of 171
Page 1 of 7 1 2 3 4