Search:

Type: Posts; User: JOHNGEAR; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Right on then, thanks for clearing this up I am...

    Right on then, thanks for clearing this up I am now ready to play.
    I also now understand the difference between Autocal to Flashscan.
  2. Ha! I think I got it. I open the V8 - look at the...

    Ha! I think I got it. I open the V8 - look at the quick start(double click the E38 or T43 depending what I want to look/edit)-calibration summary opens-click F5 edit- then because this option is not...
  3. I also just may have been frustrated when I saw...

    I also just may have been frustrated when I saw the word Autocal and did not understand what was going on so I posted the phase Autocal to have someone experienced correct me where it is needed,...
  4. You have made me wonder if my 7.5 was up to date...

    You have made me wonder if my 7.5 was up to date so I just made sure it was updated with V7.5.7.245.
    I though that when I check for up dates in the V8 it would do both so I just wanted to be sure.
  5. I will try to provide the missing information...

    I will try to provide the missing information required so I (and others reading) can get the best advice you may have to offer with my issue posted. Please understand, playing with this new truck is...
  6. wanted to show a pic of what i run into

    wanted to show a pic of what i run into
  7. thank you for your assistance but i still cannot...

    thank you for your assistance but i still cannot read the settings for the t43 when i try to use 7.5 just as i would with my ls1b tune. still telling me flash/scan is not compatible, i do see others...
  8. Not understanding why I would need Autocal to read my T43 in a 2010 Silverado

    Hello.
    I just acquired a 2010 Silverado and do not have an issue reading the E38 but when I try to read the T43 the pop up commands me to update my firmware through the control panel because the...
  9. Replies
    18
    Views
    11,488

    Hello. Thanks for your comments, they are...

    Hello.
    Thanks for your comments, they are reassuring. Yes I did come off the throttle a bit so that there could be it. I will do it again (all out) to see what it comes up with and post the log....
  10. Replies
    18
    Views
    11,488

    Sorry about not responding right away(work...

    Sorry about not responding right away(work things) but to answer your question it go as follows: out of the V1 super charger=2.75" into 3" air to water cooler out 3" reduces to 2.5" then into a...
  11. Replies
    18
    Views
    11,488

    jut realized, it could be a pressure drop from...

    jut realized, it could be a pressure drop from the inter-cooler. Feedback?
  12. Replies
    18
    Views
    11,488

    Hello all. I found a way to eliminate the belt...

    Hello all.
    I found a way to eliminate the belt slippage (yea!) I added another idler pulley that has an adjustment slot so I release the tensioner and position the new idler pulley down the slot...
  13. Replies
    18
    Views
    11,488

    This is where it was loosing boost(regulating it)...

    This is where it was loosing boost(regulating it) as I have one installed on each plenum riser. I disabled it by tightening the springs to coil bind. Now(after a few runs) at 12# boost I think I hear...
  14. Replies
    18
    Views
    11,488

    Still, I am thinking I should upgrade to a V7 YSI...

    Still, I am thinking I should upgrade to a V7 YSI for real power.
  15. Replies
    18
    Views
    11,488

    more

    more
  16. Replies
    18
    Views
    11,488

    Great news!! It was a boost leak. Corrected it...

    Great news!! It was a boost leak. Corrected it and now I see the gauge just peak past 10# but run out of road tonight.
    Fast, pulls hard all through 2nd then into 3rd but no road to continue. Will...
  17. Replies
    18
    Views
    11,488

    Too small of a supercharger after dyno results

    http://img42.imageshack.us/img42/9685/cakwhfjcxtdmddzjoiptls.mp4Well did a dyno day to get the tune corrected(we did as the wide band shows a good flat A/F ratio) but the results did not end well....
  18. Replies
    10
    Views
    6,813

    I just noticed that I did not follow the AutoVE...

    I just noticed that I did not follow the AutoVE instructions as stated. The commanded AFR needs to be set to something other than 14.63 to prevent O2 narrow band from using STFT. Question, can i just...
  19. Replies
    10
    Views
    6,813

    Hello, this is my tune(changed a few things) and...

    Hello, this is my tune(changed a few things) and it is what the logs 4 & 5 are from without adjusting anything.
    The logs are street(some long boring parts) and have not done anything to them....
  20. Replies
    10
    Views
    6,813

    I hope the input provided here will help others...

    I hope the input provided here will help others with the same questions pertaining to the Auto VE using the F.A.S.T. duel wide band O2 sensors as it has answered my questions. Thank you to all with...
  21. Replies
    10
    Views
    6,813

    I hope this is what you are looking for. It was...

    I hope this is what you are looking for. It was all I got with the unit. Maybe this web site will be more help for you.
    ...
  22. Replies
    10
    Views
    6,813

    Thank you, now with these options for the...

    Thank you, now with these options for the controller(F.A.S.T.), one would want to use the high res mode for the external input correct? I tried the simple mode and wow, it was way off.
    • Analog...
  23. Replies
    10
    Views
    6,813

    Would these be correct for the pids that I would...

    Would these be correct for the pids that I would need?
    SAE.TP
    CALC.BEN_F1
    CALC.BEN_F2
    GM.AFR
    SAE.ECT
    SAE.RPM
    EXT.AD1
    EXT.AD2
    SAE.IAT
  24. Replies
    10
    Views
    6,813

    AutoVE with F.A.S.T. duel WBO2set up

    Hello all, I have come up with a start for my tune but need to continue with an auto ve. I just loaded this tune so when looking through the log, you will see it stall on me near the beginning. Not a...
  25. Replies
    8
    Views
    5,062

    Here are the pics. Hope this upload works. ...

    Here are the pics. Hope this upload works.

    http://img10.imageshack.us/img10/9476/004bwt.jpg


    http://img825.imageshack.us/img825/1016/005wr.jpg

    ...
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4