Search:

Type: Posts; User: Tre-Cool; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    1,032

    I haven't posted the full cax file. my question...

    I haven't posted the full cax file. my question is still around how or if it's possible to define all the gearshifts in 1 table vs individual.
  2. Replies
    18
    Views
    2,554

    Sticky: not so much a beta software question, but figured...

    not so much a beta software question, but figured if/when it happens it'll only be a v8 option.

    So my question is, Can bus expansion port on the v3. What was the intention or capabilities of it?
    ...
  3. Thread: E81 Support?

    by Tre-Cool
    Replies
    22
    Views
    5,221

    the ford stuff can be done with Forscan. I just...

    the ford stuff can be done with Forscan. I just used my obdlink device with it to read the bcm config out, change the parameter, then sent it back.

    Apparently the ford dealers know that it can be...
  4. Thread: E81 Support?

    by Tre-Cool
    Replies
    22
    Views
    5,221

    my dad's ford ranger has/had that stop/start...

    my dad's ford ranger has/had that stop/start bullshit in it too. $20 later for some software and it's turned off in the bcm.
  5. Replies
    48
    Views
    30,500

    scrap the unsigned/signed question. i kinda...

    scrap the unsigned/signed question. i kinda worked it out myself. 10k rpm for instance would never work as a 16 bit integer.

    I was wondering if it was possible to go above the 8192rpm limit.
  6. Replies
    48
    Views
    30,500

    "If you are at a tps and your mph is lower, it...

    "If you are at a tps and your mph is lower, it will downshift."

    Correct, but if you look at the TUTD shift speeds, the factory generally max's the upshift out but it still lets you control the...
  7. Replies
    48
    Views
    30,500

    So i found the limiter & it is linked to Output...

    So i found the limiter & it is linked to Output Shaft RPM.

    In the 2 os files i have which are compatible, the raw hex value is the same.

    01 00 B0 40 AD 70
    24212
  8. Replies
    48
    Views
    30,500

    24208 24209 Heres 1 of my cars with the...

    24208
    24209
    Heres 1 of my cars with the 24256025 OS. For comparison i've attached a compatible OS that i normally replace with the 6025.

    I spent some more time playing with 1 of them yesterday...
  9. From postings i've seen on the hpt board, the...

    From postings i've seen on the hpt board, the caprice trans tune seemed to suffer the worst of the convertor not holding lockup. Try changing the valve offset to 50-60psi. (i use anywhere from...
  10. Replies
    48
    Views
    30,500

    So thread dig again, now that i'm have been...

    So thread dig again, now that i'm have been building cax files and going through some t43 bin files. I did some testing on 2 of my own cars which are running the same os/cal but have different gear...
  11. I've done a few for the exact same reason. if...

    I've done a few for the exact same reason. if your still chasing them post the os/cal.

    here is 1 i did for os 24256025
  12. Replies
    3
    Views
    1,032

    Multiple gear shift speed table

    Been going through t43 calibrations and adding a lot of undefined tables to test, some of the late vf commodore ones don't have the the tapshift speed's defined so i found & added them, but i did...
  13. Replies
    2
    Views
    1,314

    Expansion Port

    So the website has "Connects third party data loggers to FlashScan V3 and AutoCal V3 via CAN. Currently no third party CAN data loggers are supported. This feature is reserved for future expansion."...
  14. Replies
    1
    Views
    323

    V3 Serial Port Pinout

    Got my new V3, but didn't realize it doesn't come with the serial adapter cable like the old v2's did. so was going to make 1 up, since i have the molex plugs already.

    From looking at the pictures...
  15. I'm the opposite, i use efi for most of my...

    I'm the opposite, i use efi for most of my tuning/logging. hpt editor for stuff we don't have. very rarely use the scanner because it irritates me that they never linked the 2 like we have in...
  16. Replies
    21
    Views
    21,084

    since it uses the same calibration numbers as the...

    since it uses the same calibration numbers as the trucks, can you just use a truck cal?
  17. Replies
    18
    Views
    12,327

    Just an FYI if anyone ever needs to get this to...

    Just an FYI if anyone ever needs to get this to work.

    Tried a spare ecu in a colorado, had to disable vats, & change the vats type from 2 to 3.

    Without changing vats type, no fuel pump would...
  18. I've been doing some testing recently on an e38...

    I've been doing some testing recently on an e38 controller with trying to restrict throttle/power by using the TCS Throttle Limiter by gear table & relevant switches for throttle/spark.

    In short...
  19. ive never experianced the issue on any e38/e67...

    ive never experianced the issue on any e38/e67 i've tuned with efilive.

    probably more of an issue restricted to hpt with their custom ve OS.
  20. drop your b1829 tables in the upper rpm. match...

    drop your b1829 tables in the upper rpm. match them to your idle speed, bet it drops real fast then.
  21. Replies
    3
    Views
    3,788

    been running for 4yrs like that no problems.

    been running for 4yrs like that no problems.
  22. Replies
    360
    Views
    271,206

    Sticky: i ended up pulling out .2 across the board and...

    i ended up pulling out .2 across the board and that seems to be good enough.
  23. Replies
    43
    Views
    35,895

    yep. definitely only a problem with the v8...

    yep. definitely only a problem with the v8 scanner. the ad4 voltage never moves from 0 volts.


    23440

    running latest firmware and even updated all the files on the device.
  24. Replies
    43
    Views
    35,895

    correct. i will confirm again shortly.

    correct. i will confirm again shortly.
  25. Replies
    43
    Views
    35,895

    I can't seem to get the AD inputs to show...

    I can't seem to get the AD inputs to show anything when logging in V8.

    works fine in 7.5
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4