Search:

Type: Posts; User: onfire; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    3,839

    So far cos3 is working very well on the C5. 2bar...

    So far cos3 is working very well on the C5. 2bar is almost out of range :)
  2. Replies
    0
    Views
    2,827

    Lean cold start COS3.

    Lean cold start COS3.

    Any tables other than A0008 and B3632 control coldstart?
  3. Replies
    0
    Views
    2,508

    Can you load a cal into a COS without an ECM?

    Trying to figure out how to load a cal into COS3 just using a desktop computer. Is it possible?
  4. Replies
    2
    Views
    3,839

    COS 3 or COS 5 for 2000 Corvette?

    I converted a 1999 firebird to a COS5 for a 3bar set-up. Was a pain since I could not use the 1999 OS, but cut and paste was my friend. Worked very well.

    Now working on a 2000 Vette for a friend....
  5. Replies
    0
    Views
    2,411

    COS 3 or COS 5 for a 2000 corvette?

    I converted a 1999 firebird to a COS5 for a 3bar set-up. Was a pain since I could not use the 1999 OS, but cut and paste was my friend. Worked very well.

    Now working on a 2000 Vette for a friend....
  6. Thanks. Willtry that short term.

    Thanks. Willtry that short term.
  7. Any reason not to run OLSD fulltime in noncos?

    If I set the high/low octance tables the same. Leave KR enabled for safety. Turn off strims, ltrims and O2's. Then tune for sd as normal, then enable the maf? For a 2000 Vette.

    Later will add COS5.
  8. I'll get one today. Thanks.

    I'll get one today. Thanks.
  9. http://www.efilive.com/supvehicle.aspx This...

    http://www.efilive.com/supvehicle.aspx

    This list shows it will support some 2007 6.0 ecms and will not suppoort some 2007 ecms.

    The truck is a Chevrolet 2007 2500hd 6.0 with a 6 speed automatic...
  10. Does V1 have the capability to tune a 2007 6.0 Chev truck?

    Sorry for the dumb question, but I have not kept up with the various ecm's.

    2007 vortec 6.0 truck.

    Thanks
  11. COS5...which table controls the commanded AF

    With A0008 set at 1.0 everywhere, my commanded AF at start is 11.1 : 1 After it idles for a few seconds it keeps leaning out until B3647 takes over.

    I can manipulate it with A0008, but with A0008...
  12. Guess I'll end this thread..... 2.0 seconds was...

    Guess I'll end this thread..... 2.0 seconds was too much delay for forcing sd for me....much easier to set it at 0 and force it during the crank at 300rpm, then it's in sd when the engine fires.
  13. Thread: who to fix RR?

    by onfire
    Replies
    3
    Views
    3,726

    Yep. I've tried the crank relearn, hard reset,...

    Yep. I've tried the crank relearn, hard reset, soft reset, flash through the aldl, emulation flash through the USB, clear all DTC's and it will reset with the key on engine off. Drop the same program...
  14. Thread: who to fix RR?

    by onfire
    Replies
    3
    Views
    3,726

    I email craig moates. Mine stays wacked with a...

    I email craig moates. Mine stays wacked with a p1336 code.

    craig@moates.net
  15. Which maf fail numbers are you using for C2907 and C2908?

    I had a problem with my car not starting with a known tune when I used 400rpm for C2907 and 2.0 seconds for C2908.


    When I changed C2907 to 300rpm and C2908 to 0 seconds the starting problem is...
  16. Replies
    6
    Views
    5,098

    12580698 is the correct part number for a 2bar...

    12580698 is the correct part number for a 2bar bap sensor...should have a brown label and look like the 1bar factory sensor.

    Sounds like you have the scalar set incorrectly...should be around 188....
  17. Thread: Start up A/F's

    by onfire
    Replies
    4
    Views
    3,407

    b3661 also works

    b3661 also works
  18. Thread: Start up A/F's

    by onfire
    Replies
    4
    Views
    3,407

    b3632 will work...plus it has a decay rate.

    b3632 will work...plus it has a decay rate.
  19. Replies
    18
    Views
    8,292

    That's pretty good detective work! Now we know...

    That's pretty good detective work! Now we know why it doesn't work. Could EFI develop a work-a-round?
  20. Replies
    3
    Views
    4,923

    Thanks

    Thanks
  21. 3.1 injector what's the engine combo? Might be...

    3.1 injector what's the engine combo? Might be out of injector regardless of dc....should be pig rich.
  22. I just tuned in a set of 86lb low imp injectors...

    I just tuned in a set of 86lb low imp injectors with EFI on a ls1 computer. Wouldn't know where to start on the LS7 PCM.

    Some of the LS7 files are helpful though.
  23. Replies
    9
    Views
    5,846

    Post up a tune.

    Post up a tune.
  24. I've tuned two turbo systems on the ls1 platform....

    I've tuned two turbo systems on the ls1 platform. This new E38 platform is wayyyy over my head....ve calcs instead of tables, etc....incredible tuning power there.
  25. Figured it out...had to strip EFI off the...

    Figured it out...had to strip EFI off the Document files also and reinstall....all is good.
Results 1 to 25 of 180
Page 1 of 8 1 2 3 4