I was just wondering what where the main differences between seda and ute files? Apart from fuel tank settings diff ratio etc etc. Say you had to flash a tuned ute back to factory and you didn't have...
Type: Posts; User: Picto; Keyword(s):
I was just wondering what where the main differences between seda and ute files? Apart from fuel tank settings diff ratio etc etc. Say you had to flash a tuned ute back to factory and you didn't have...
After the factory trans file
Hi just chasing a factory file for a HSV VE GTS 2007 LS2 24239353 op system and 24239647 cal. If anyone has one it would be greatly thanked as i haven't been tuning long and this file is pretty...
Its out of a 2009/2010 Holden VE 6.2ls3 maloo ute 2x4
engine op system is 12635863
Hi just trying to locate factory file 24254909. Had a look on holdencrazy but was unable to find one.
This is out of a Holden Maloo
Thanks
I have just pulled a tune file out of car i was contacted because the car had lost drive and pulled an engine light. i haven't had a heap of experiance with tuning these and am unsure on how to...
Running mafless due to being auto. that was the same advise i was given
I must have been having a blonde moment yesterday becuase that wasn't the file out of the car. Ok I'm running mafless 2 bar, i have checked to make sure that map reads 100kpa at key on, throwing maf...
I wasn't involve the the motor combo just got given it to tune!! i will post them soon when i get home. Anything would would like to see??
Hi all.
I'm tuning up a twin turbo SS commodore which i seemed to be having a few issues with. I have done forced induction cars before but only one turbo. I'll give you a run down of the vehicle...
Hi was just wondering if someone had a factory file cal number 92187911. Had to put an exchange computer in there and am after fuel gauge settings really cause it ain't even close!!!!:bad:
Thanks
Thanks Champ thats all i need, i just wanted to check some fuel gauge settings.
Hi, Just chasing a factory file from a 2010 VE SS ute manual op system 12635863. If any one could help would be great.
Thanks
Thanks joecar the car now drives like it hasn't ever before the customer is stoked and so am I. Thanks again for the time and the advice it REALLY was a big help
Thanks for the file, I've just made the changes and about to give it a go, thanks again for the advice
Thanks joecar i will try that out and let you know how i go. I must admit i don't overly understand the TPS VE and how it works i do need to do some research on it.
Any other tutorials that you...
Here is the tune, i'll need to get the logs off my other computer.
as far as i know for the motor its a 7lt LS7 heads and manifold 60lb injectors fuel system std hsv headers high flow cats and...
HELP!!!!!!!
Having major issues with a holden 5.7ltr that has been pulled out a 7ltr built motor with a V7 vortec side mount blower running only 8psi, running a factory cam (only to get road...
I was wondering if anyone else had a wide band 2 and would be able to tell me the colour combo of the wires at the plug closest to the sensor, I wiped my plug out of a speed hump and lost the plug!...
ok will try that out at some stage today. I don't but i will get log of it when i check that table.
The car is mafless also
Thanks Joecar
9034
Yeah sure have i've been from whats in there now all the way up 105.
Anyone who wants to offer any advice either pos or neg would be welcomed.
Cheers
Hi, I'm having a few trouble at the moment trying to tune up a VZ Holden 5.7ltr with ETB. I seem to hit this code "P0068" only at high rpm normally during a power run and i can't seem to get around...
I've got a customers car who had a ls3 installed into a ls1, The car is popping at idle hard to start and pulls a cam sensor code. After pulling the sensor i found the cam wheel is a 4x ls3 type not...
Every time i try to load a pid selction onto the BB it get half way through and brings up an error message. "Error:$0194; write failure". Anybody seen this before?
Also to i wondering if my laptop...
i will log and see what happens, i'm doing a hvt1900 blower next so i will give it a go.
Anything you that i should be logging that i may not have been?
Thanks for the advice