Search:

Type: Posts; User: GMPX; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    14
    Views
    1,377

    I will check on Monday but at this stage they...

    I will check on Monday but at this stage they have been assigned the task of validating some of the ECM's that have been added in to the V8 tune tool.
  2. Replies
    3
    Views
    1,672

    Unfortunately forum posts get missed, that OS has...

    Unfortunately forum posts get missed, that OS has been supported since August last year!
    Pretty sure that will be supported in this release here....
  3. Replies
    3
    Views
    96

    Yeah I think that was correct (less than 10%),...

    Yeah I think that was correct (less than 10%), the sensor recalibrates to a non ethanol fuel.
  4. Thread: 2012 lml issues

    by GMPX
    Replies
    15
    Views
    376

    These have all been removed from the software for...

    These have all been removed from the software for MANY years now. Anyone doing this stuff is not using EFILive.
  5. Replies
    2
    Views
    200

    Yes, all of the later model ECM's (I think there...

    Yes, all of the later model ECM's (I think there is about 5 of them) have had scanning support added into V8 but that is not yet released as a beta I'm afraid.
    In the meantime you could try in V7.5...
  6. Thread: P08 Pinout

    by GMPX
    Replies
    9
    Views
    174

    Probably a project that should never have...

    Probably a project that should never have happened to be honest, horrible PCM that one.
  7. Thread: P08 Pinout

    by GMPX
    Replies
    9
    Views
    174

    Yeah that's the trick, those four wires I...

    Yeah that's the trick, those four wires I mentioned are common for all those PCM's that look like that.
  8. Thread: P08 Pinout

    by GMPX
    Replies
    9
    Views
    174

    Yes it has less pins but the important ones are...

    Yes it has less pins but the important ones are in the same spot.
    The LS1B bench harness I have runs all those PCM's you've listed there, V6-P04, Northstar-P06, they are all the same pinout for...
  9. Thread: P08 Pinout

    by GMPX
    Replies
    9
    Views
    174

    Pretty sure it is the same as the LS1B.

    Pretty sure it is the same as the LS1B.
  10. Replies
    2
    Views
    179

    I think it is handled in another module on the...

    I think it is handled in another module on the later vehicles (someone may correct me on that).
  11. Thread: 2014 os

    by GMPX
    Replies
    2
    Views
    171

    I think 32370231SB was the latest one supported...

    I think 32370231SB was the latest one supported for conversion, we have plans to update all the latest OEM 2013-2018 releases to CSP....at some stage.
  12. Replies
    10
    Views
    552

    I agree and it is getting worse, just like other...

    I agree and it is getting worse, just like other tuning companies copy and steal our custom OS work to profit from. I feel sorry for them if that is the best they can come up with.
  13. Replies
    12
    Views
    1,760

    Sorry, I'm still not sure what you are referring...

    Sorry, I'm still not sure what you are referring to by "base engine cal and diagnostics adaptives".
    This stuff is probably stored in the same area as the VIN etc that is not altered during a flash.
  14. Thread: CSP5 Switch

    by GMPX
    Replies
    2
    Views
    142

    No the position is forgotten when the ECM is...

    No the position is forgotten when the ECM is programmed.
    Tunes can be set up to default to a particular tune after the ECM is programmed though.
  15. Replies
    12
    Views
    2,954

    These things always cause problems, you'll...

    These things always cause problems, you'll probably have to do this everytime you flash.
  16. Replies
    10
    Views
    552

    I don't recall there was such an error for the...

    I don't recall there was such an error for the E98 *, for a locked E98 a user would get '$0537' - Controller is locked with a custom key. * Happy to be corrected on that.



    Re the error...
  17. Replies
    10
    Views
    552

    Read block on the E98 cannot be applied to the OS...

    Read block on the E98 cannot be applied to the OS like a Bosch or Cummins ECM, in fact you can't read an E98 without sending down an executable bootloader to do so because the ECM supports no such...
  18. Replies
    12
    Views
    1,760

    What are you looking for specifically with that...

    What are you looking for specifically with that question? As in what do you want to see reset?
  19. Replies
    12
    Views
    1,760

    Calibration Flash = All calibrations segments are...

    Calibration Flash = All calibrations segments are flashed regardless if changes in certain ones have been made or not.
    Full Flash = All calibration segments and the operating system are flashed.
  20. Replies
    36
    Views
    10,887

    Sticky: We have updated software to work with this one....

    We have updated software to work with this one.
    Can you send an Email to support@efilive.com and we'll get you sorted out.
  21. Replies
    14
    Views
    1,377

    The person that works on these is away until the...

    The person that works on these is away until the end of January.
  22. Thread: cm871

    by GMPX
    Replies
    6
    Views
    4,679

    Yeah the alternate method to reading those...

    Yeah the alternate method to reading those earlier ECM's seem to be working ok.
    The editing of those earlier ECM's is not a high priority to add unfortunately, people in this market seem happy to...
  23. Replies
    4
    Views
    292

    You need to get the P/N's off the old ECM. There...

    You need to get the P/N's off the old ECM. There will be printed on the sticker an 'E/C' code, that is what people will need to get the correct match tune.
  24. Thread: Dodge ram 2350B

    by GMPX
    Replies
    6
    Views
    305

    Not on here, deletes are not supported in this...

    Not on here, deletes are not supported in this software.
  25. Replies
    36
    Views
    10,887

    Sticky: Yes the updates are done for the one you are...

    Yes the updates are done for the one you are dealing with, will post links up this week.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4