Search:

Type: Posts; User: 2002_z28_six_speed; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    2,000

    Things have been going super slow over here. I...

    Things have been going super slow over here. I can't believe its taken me so long to respond. I do appreciate the sanity check. I grabbed a stand alone harness correct for a 2002 vehicle and I am...
  2. Replies
    3
    Views
    2,000

    Swap question 512 versus 1 mb pcm

    I am starting up an ls swap into a vintage car using an LQ4 Gen 3 and 4L80. At this point the wiring harness and PCM has not been chosen.

    My 1st question is there any 1MB PCM with cable throttle?...
  3. Replies
    4
    Views
    5,030

    Thank you for your many years of helping others....

    Thank you for your many years of helping others. I have it in COS right now with MAF disabled. I used the MAF at least to help tune some of the VE and then cut her loose.
  4. Replies
    4
    Views
    5,030

    Good to know. I will try it then. The guide does...

    Good to know. I will try it then. The guide does read as though the MAF will be disabled and not an option. Probably just an oversight as you are suggesting.
  5. Replies
    4
    Views
    5,030

    COS question for LS1B

    I have a technical question about COS. I have a 2003 Sierra with the LS1B operating system. I believe 12579405 if it matters.

    Anyways my question is about turning off the MAF. It came to my...
  6. Sticky: I have a dumb question if this is allowed. Is it...

    I have a dumb question if this is allowed. Is it suggested/recommended to run this process with STFT only?
  7. Feels like I am in tuning hells BTW. LOL. I...

    Feels like I am in tuning hells BTW. LOL. I should have just dropped a bone stock motor in. :(
  8. Jerking when vehicle is at rolling idle.

    Tuning has progressed a bit but now I have hit a nasty snag. Current tuner does not seem to be able to crack this one.

    When at a rolling idle. Clutch is out. 0% on the gas. The vehicle will roll...
  9. In the last weeks I was convinced, begrudgingly,...

    In the last weeks I was convinced, begrudgingly, to remove some of the aftermarket components from my vehicle.

    I removed the aftermarket performance intake and went back to the stock throttle...
  10. a couple of weeks. ideally. the truck has been in...

    a couple of weeks. ideally. the truck has been in the garage for months. i live in a dense city so driving a stalling vehicle gets annoying.

    the vehicle has a manual transmission. the setup is...
  11. I did some tuning with pat G and none of the...

    I did some tuning with pat G and none of the files he sent me really made anything better and then I did some tuning with lsx power tuning. did the live session and after about an hour or so it...
  12. OK but that doesn't solve the problem. Anyone can...

    OK but that doesn't solve the problem. Anyone can make a comment like that.
  13. If it helps sure.

    If it helps sure.
  14. RPMs coming down too fast and stalls. Car does not respond to changes?

    Hired a tuner. He has changed the desired air flow, TC, TF many times over the course of an hour and we cant get the engine to stop stalling after a blip of the throttle.


    I have a 408 with a...
  15. I actually have new knock sensors and harness!...

    I actually have new knock sensors and harness! Yay for me! I finished up the engine rebuild about 3 months ago and it was a total refresh aside from breaking into the short block.

    New oil pan...
  16. I tried pulling spark advance till the engine ran...

    I tried pulling spark advance till the engine ran like a snail and the knock never went away.

    My guesses are that it is mostly all fake knock due to the engine or burst knock shows up as KR as...
  17. :UPDATED: I think I finally graduated with a...

    :UPDATED:


    I think I finally graduated with a C- from the school of hard knocks today. The truck ran pretty good with minimal dipping of the idle or surging ( solved with the desired airflow and...
  18. I would say that I could see .98 to 1.14 BEN in...

    I would say that I could see .98 to 1.14 BEN in some cells while others are tighter.


    One thing I noticed is the AFR will be great for awhile. 14.8. Then I get into traffic for 20+ minutes and...
  19. Well my bike got a flat (and I didn't die!!) so I...

    Well my bike got a flat (and I didn't die!!) so I have been forced into working on this yet again. Reporting in that results are much better with the new (correct) injector data. Practically no...
  20. Statesman, I wanted to let you know that you...

    Statesman,

    I wanted to let you know that you were right about the injector data. I started looking at it and it didnt make sense. At one point in time I was talking to a tuner (didn't end up...
  21. Seems drastic to just fix the hunting idle issue...

    Seems drastic to just fix the hunting idle issue that remains at this point. BUT I am willing to try it. You guys know your s$#it. :)

    I got the fuel injector data from a stock tune I got off...
  22. 2004 Yukon Denali. Stock LQ4 bottom end. 6.0L...

    2004 Yukon Denali.
    Stock LQ4 bottom end. 6.0L engine
    Precision Heads, 5.3L heads, stage 2.5
    Texas Speed 224R cam, this is a 224/224 cam with .581 lift, 114 lsa
    Kooks catted 1 3/4 headers with...
  23. I am still blown away that I didn't know the...

    I am still blown away that I didn't know the difference between 1 trip and 2 trip. :wallbash: Maybe I should go back to riding my sport bike. haha.
    Is there a technical document that I can run...
  24. Oh man! It looks like I am using an out of date...

    Oh man! It looks like I am using an out of date document for the VE tuning process.

    Just tried searching the site a little bit --- Is there an official latest version with the basics of what to...
  25. LS2 Corvette injectors. Factory OEM Bosch.

    LS2 Corvette injectors. Factory OEM Bosch.
Results 1 to 25 of 312
Page 1 of 13 1 2 3 4