Search:

Type: Posts; User: thunder550; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    57
    Views
    41,862

    Subscribing for updates. I just read out my 2011...

    Subscribing for updates. I just read out my 2011 A50 24259875/24259876 file successfully and emailed it to support@efilive.com. Is there mapping/editing functionality in the works?
  2. Replies
    137
    Views
    95,033

    Just realized that has to be a kpa value, the...

    Just realized that has to be a kpa value, the table only goes to 146ish psi. I just tried setting the 400 and 600 ft-lb column to 900 kpa from 50-600 RPM, still not getting lockup until the 2-3...
  3. Replies
    137
    Views
    95,033

    Is this 800 kpa? I have D5233 set to Disable,...

    Is this 800 kpa? I have D5233 set to Disable, D5231 and D5232 are at stock values, and set the D5072 as shown in the screenshot below (values are in kpa). I haven't gotten consistent lockup in 2nd...
  4. Replies
    4
    Views
    4,294

    Anybody have any ideas?

    Anybody have any ideas?
  5. Replies
    4
    Views
    4,294

    Also, it seems to be wiping the learned shift...

    Also, it seems to be wiping the learned shift times every time I flash the TCM. I was told to read out the existing calibration file, adjust, and reflash, so that's what I've been doing, but every...
  6. Replies
    4
    Views
    4,294

    I just tried that. Same results, if not worse. On...

    I just tried that. Same results, if not worse. On a WOT run from a standstill the ramp rate seems to be slower even using the same settings, and I'm not getting lockup until after the 2-3 shift....
  7. Replies
    4
    Views
    4,294

    Help with WOT converter lockup

    I've been playing with my TCM tune trying to get the converter to lock up at WOT. I set D5233 TCC Apply Slip Inhibit to Disable and increased the on ramp rates in D5072. Currently the values are...
  8. Replies
    5
    Views
    4,551

    Yep that's me :) I'll be out there Friday night!...

    Yep that's me :) I'll be out there Friday night! I'll bring my laptop, if you can just give me a quick overview of that table that would be awesome, I can play around with the values and do some...
  9. Replies
    5
    Views
    4,551

    Reducing smoke prior to turbo spool

    How are you guys reducing smoke output when the throttle increases before the turbo spools? If I'm cruising along and nail the throttle, I get a large cloud of dark smoke out the tailpipe until the...
  10. Replies
    6
    Views
    3,686

    Probably. Most tuners save the tune files, either...

    Probably. Most tuners save the tune files, either by vin or name. Again, it depends on the tuner though.
  11. Replies
    6
    Views
    3,686

    Depends on whether or not the tuner locked the...

    Depends on whether or not the tuner locked the ECM.
  12. Replies
    0
    Views
    1,525

    Reading other modules in 2011 GMC Yukon

    Trying to figure out how to scan other modules in the vehicle for trouble codes. My wife's Yukon just came up a couple days ago with a Service Traction Control and Service Stabilitrak message, but no...
  13. Replies
    3
    Views
    2,967

    Yep, I have a BlueFusion add-on bluetooth device...

    Yep, I have a BlueFusion add-on bluetooth device that communicates on the CAN bus, I have to disconnect it whenever I want to flash the ECM because it causes communication issues. How does your...
  14. Yeah I just disabled my Baro tables by setting...

    Yeah I just disabled my Baro tables by setting them to always run in the C tables. I haven't had any issues yet, and now the DSP5 is working as it should.
  15. Replies
    7
    Views
    6,164

    Any chance the MAF wires could be shorting out on...

    Any chance the MAF wires could be shorting out on something? I've read about a few different areas where the wiring harness passes hard corners that can wear through it.
  16. Replies
    6
    Views
    3,938

    Is it a stock cam, throttle bdy, etc? Might need...

    Is it a stock cam, throttle bdy, etc? Might need to tweak the idle airflow tables a bit.
  17. For turbo brake, you can just set the Turbo Vane...

    For turbo brake, you can just set the Turbo Vane Target Position to 99% from 2200 RPM to the end of the table, and 0-5.0 for the fuel quantity. Basically that's telling the ECM to close the turbo...
  18. Awesome, thank you!

    Awesome, thank you!
  19. Done, thanks!

    Done, thanks!
  20. GM.BOOST_DMA not available as a BBL PID for E60 controller?

    I'm trying to get my V2 set up to BBL with the same PID selection I use when logging with my laptop. I noticed that GM.BOOST is available, but GM.BOOST_DMA is not. I would just switch, but...
  21. Thanks guys. I made the changes to the baro...

    Thanks guys. I made the changes to the baro tables, everything seems good so far.
  22. What are the downsides to disabling the A, B, C elevation tables?

    I live at 7400 ft and I'm trying to figure out the best way to get a DSP5 tune set up to work here. The issue that I'm up against is that the barometer here at my elevation reads about 11.2-11.3 psi,...
  23. Replies
    29
    Views
    19,202

    Food for thought... ...

    Food for thought...

    http://losangeles.cbslocal.com/2012/09/18/study-air-pollution-from-burger-joints-worse-than-trucks/
  24. Replies
    0
    Views
    1,989

    PLX wideband setup with serial output

    sold
  25. Ok so if my speedo is off I need to change it in...

    Ok so if my speedo is off I need to change it in the ECM then instead of the TCM?
Results 1 to 25 of 178
Page 1 of 8 1 2 3 4