Search:

Type: Posts; User: trimchip; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    6,549

    Check under: Help - Register EFI Live. If...

    Check under:

    Help - Register EFI Live.

    If you innstalled th SW on a new PC you have to fill in licence info for Flashscan unit and the RR.

    IE two licences. One for the Flashscan and one for...
  2. Std tune. Cleaned main terminals on battery and...

    Std tune. Cleaned main terminals on battery and main grounds. Also cleaned connectord to Pcm.
    Checked for leaks on manifold - none. Also coil #5 was misfiring periodically under load.
    I think a bad...
  3. Replies
    7
    Views
    6,549

    My pc often does not find it first time. Try to...

    My pc often does not find it first time. Try to unplug and connect it again.
  4. Replies
    7
    Views
    6,549

    Try re innstalling the ftdi drivers. Make shure...

    Try re innstalling the ftdi drivers. Make shure your shortcut opens the version you innstalled lately, and not the old one.
  5. Strange advance behavior - 2006 Silverado 5.3 LS1B controller

    Engine misfires under medium and full load, and sometimes under steady conditions.

    Advance and KR behaves strange.

    Could it be a sensor fault?

    1831418315
  6. Replies
    26
    Views
    18,095

    Changed it under properties and restarted...

    Changed it under properties and restarted program.

    Now it shows EQR, and the tables changed to higher than 1
  7. Replies
    26
    Views
    18,095

    You are right (of course) :) I saw this...

    You are right (of course) :)

    I saw this earlier today when i was reading through the custom OS 2/3 bar tutorial. (It reads Lambda in my setup)
  8. I found the RTACS Settings for Roadrunner under...

    I found the RTACS Settings for Roadrunner under Edit-Properties-Roadrunner :)
  9. No difference with or without filters. Using...

    No difference with or without filters.

    Using coarse control, but I have not changed updating freq for RTACS. I think I saw an explanation somewhere.

    It`s been a while since I used EFI Live and...
  10. RTACS using EXT.WO2AFR1,GM.AFR and CALC.BEN1

    I`m trying to alter the Main VE Table using EXT.WO2AFR1,GM.AFR and CALC.BEN1

    I have read most of the articles regarding the theme in this section and in the Gen III, but I`m still unabe to set up...
  11. Replies
    5
    Views
    6,158

    I`m having the same problems. RTACS is active...

    I`m having the same problems.

    RTACS is active and updaing using a custom operative system, but not on my normal 12212156 OS . .

    I have read all the articles related to...
  12. Replies
    26
    Views
    18,095

    The article starts with numbers higher than 1...

    The article starts with numbers higher than 1 giving a lower AFR.

    It`s the opposite with mine, tables B3605 and B3618 contains multipliers lower than one.

    Anyway, I`m struggling to obtain auto...
  13. Replies
    26
    Views
    18,095

    RE start of thread: Does B3618 or B3605...

    RE start of thread:

    Does B3618 or B3605 Control Commanded Fueling..

    Test: 2002 LS1B OS 1221256

    I suppose 1221256 is a misprint, and that we are actually talking about 12212156

    If this is...
  14. Replies
    0
    Views
    2,593

    LY6 E38 PCM to LS1B PCM convertion?

    I bought a 2008 LY 6 engine, which came with some of the engine harness cut.

    I`m mostly experienced with the LS1B ECM, and I do have a roadrunner.

    Instead of spending time and money to get the...
  15. I figured it out, in my set up I have to be...

    I figured it out, in my set up I have to be logging. If I`m only monitoring RTACS does not activate. As soon as I logged (red button) RTACS fired up just fine :-)
  16. And my Tune tool for sure states "RTACS is NOT...

    And my Tune tool for sure states "RTACS is NOT active " :-(
  17. BTW I did check the link`s in the scan tool PID...

    BTW I did check the link`s in the scan tool PID vs the tune tool links etc.
  18. Not lucky today :-( . For some reason I`m unable...

    Not lucky today :-( . For some reason I`m unable to get the connection between the scantool (which is set up correctly and logging fine) and the Roadrunner which is in emulation mode, showing it`s...
  19. Thanks a lot guy`s :-) As I`m in another time...

    Thanks a lot guy`s :-)

    As I`m in another time zone than you guy`s I`ll have to wait until tomorrow before I try this.

    I think I set the parameters so that STFT will not be enabled at all as I...
  20. But I do have a Q I hope some of you guys can...

    But I do have a Q I hope some of you guys can help me out with. . . I want to use RTACS (of course) along with my roadrunner. According to the help context, I`m to replace "B0101.RRR=CALC.BEN_LC11"...
  21. Apparantly , I WAS using a crossed DB-45 (or...

    Apparantly , I WAS using a crossed DB-45 (or something). because I tried using a longer DB-45 cable, and then it did NOT work . . .
  22. I did not do any cable modification either . . .

    I did not do any cable modification either . . .
  23. Not knowing about this thread, I just plugged my...

    Not knowing about this thread, I just plugged my ZT-2 into my V2 - scrolled through the menu, found ZT-2 - and it immedately communicated with the V2. Showing AFR on V2 display, and logging correctly...
Results 1 to 23 of 23