I pulled a file from a 2014 SRX today and sent it into support @ efilive to get mapping for it.
Anyone else needing one or wants to look at it let me know.
Type: Posts; User: vetteboy2k; Keyword(s):
I pulled a file from a 2014 SRX today and sent it into support @ efilive to get mapping for it.
Anyone else needing one or wants to look at it let me know.
Does anyone have a read on a 2014 Cadillac SRX that they could post up or email to me?
Looking to buy one and want to see what parameters are available.
Thanks
Thanks for the input and pdf, but if there was anything you come across with IAT2 in reference to anything that would reduce timing would be appreciated. Doing multiple dynos runs with a CTS-V the...
I was wondering if there was an IAT2 spark table on the Supercharged cars like the CTS-V, ZR1, and soon to be released ZL1 that's just like the usual IAT spark table.
Figure if the intercooler...
Was able to fix the problem with the Max Idle Area 1 & 2. I reduced to 1% for both and the issue has gone away. May help someone else in the future. Thanks for the help guys, got my brain thinking...
Hi Greg,
Its not learning it out unfortunately, and I don't see tables in the E40 for allowable integrator limits either. I know they are there in the earlier PCM's but don't see them in the E40...
I know Joe pretty well, and am friends with Matt at TuneTime Performance who has tuned tons of TBSS's, I will track this down. Matt and I were talking about it over memorial day bbq's and that's when...
Yea, the E40 was such a short run of engine controllers used anyway. Going to check if there are any newer OS available on TIS for the 2006 TBSS and see if that helps at all.
Also are there any Throttle Cracker or Throttle Follower airflow tables? When halving these tunes these airflow tables are important to have access to.
Having a problem with a scaled tune for a Maggie TVS 1900. TBSS is perfect except for when A/C is turned on.
Smoke tested and no vacuum leak or anything. A/C off truck runs perfectly. Once A/C is...
Paul,
Always been an issue programming a 2004 CTS-V as the PCM reboots during a write. It works ok when I de-select high speed however now when using the BBF I can't get the PCM to flash properly....
Its stoich from looking around is 13.43:1 so you would need 5.7% more fuel in your VE table over E10 93-octane
Ross,
To clarify some... in the custom OS5 after the TPS VE table A0007 reaches 8000 RPM does the car use the last column 8000rpm 100% TPS for fueling for the entire rpm or does it start back at...
That could be a possibility... I will log MAP voltage next time along with MAP value and see if I can create a custom PID.
You can use a Stock O/S and a 2BAR MAP, but as you said change the scalar and the offset. The issue is, with a Stock O/S while scanning, the MAP reading will still be pegged at 105KPA once you go...
If you use Lambda in your PE table {B3618} then it will look up your {B3601} and compute the desired fueling based upon your entered value in {B3601}.
For example say you command .88 lambda for...
I believe the narrow bands will adjust to stoich of whatever the AFR is of the fuel your running. So if pure gasoline they will adjust to stoich which is 14.68 and if E10 14.07 being stoich is stoich...
Measuring the analog voltage not connected = 4.41 and connected = 4.11 therefor the offset 4.11/4.41=.931973 How would I enter that into my calc pid. It keeps coming up as an invalid. Below is the...
http://forum.efilive.com/showpost.php?p=80112&postcount=11
Has anyone ever got a FJO wideband to read serial into the V2? I bought a universal cable from taq and hooked up the wires tonight but I get Controller not found.
I swapped Tx and Rx and still the...
What I meant by that is the sensor doesn't care what fuel your using or what % ethanol you have in your fuel, Its always going to read stoich of that particular fuel at 1.0 lambda.
B/c of different fuels and levels of Ethanol and when using methanol as well. Lambda never changes... stoich is stoich
I ordered a universal serial cable from TAq cables to hook up to my FJO, in the mean time I am trying to get the analog external 1 working properly. The FJO read 14.55 while V2 when scanning reads...
Yes, but what is the BEN for serial LAMBDA?
Thank you, haha I was way over complicating things!
I now have
factor 0.0 2.0 .2 "{CALC.LAM_FJO} / ({GM.AFR} / 14.7)"
As for the BEN for Serial...