Search:

Type: Posts; User: Yortt; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: Custom OS#5

    by Yortt
    Replies
    354
    Views
    375,359

    Sticky: That is correct, however this COS5 operating...

    That is correct, however this COS5 operating system can be tuned with other software such as HP tuners and LS1 Flash cable for example. The COS5 is only available for 512kb PO1 PCM (as far as I...
  2. Thread: Custom OS#5

    by Yortt
    Replies
    354
    Views
    375,359

    Sticky: This is only available with Tunerpro ?

    This is only available with Tunerpro ?
  3. Thread: Custom OS#5

    by Yortt
    Replies
    354
    Views
    375,359

    Sticky: I am looking at using N20 on a VZ is there...

    I am looking at using N20 on a VZ is there anywhere I can access the custom operating system 04 so I can control the Nos?
    Thanks
  4. Replies
    2
    Views
    1,913

    joecar...Thanks for the response, I am familiar...

    joecar...Thanks for the response, I am familiar with the PicoScope trace and the position of TDC on the reluctor wheel. I took a guess and set up the reluctor wheel TDC position in the middle of the...
  5. Replies
    2
    Views
    1,913

    LS1 reluctor wheel

    A question about the position relationship of the crank reluctor wheel to the crank position sensor.
    When the top dead centre falling edge on the reluctor wheel passes the crank position sensor at...
  6. Replies
    0
    Views
    2,906

    Flex fuel for an Australian commodore

    There is a lot of information on forums using a flex fuel sensor on an LS1, but nothing conclusive on an Australian Commodore. Has anybody successfully used a PO1 or P59 PCM to run a Commodore LS1 on...
  7. Replies
    7
    Views
    4,017

    GMTECH4 and Joecar got it thank you both, works...

    GMTECH4 and Joecar got it thank you both, works fine when you look in the correct place.
  8. Replies
    7
    Views
    4,017

    OK thank you.

    OK thank you.
  9. Replies
    7
    Views
    4,017

    Joecar thanks for the prompt response. The...

    Joecar thanks for the prompt response. The version I am using is V7-5-7 build 299 which works fine with an existing 01290005 auto tune however I now need to set up a manual tune.
  10. Replies
    7
    Views
    4,017

    01290005 custom operating system

    I have a 2004 lS1 Holden manual 12225074 using 7.5 software and want to upgrade to 01290005 operating system where can I find the operating system to load into the PCM with 7.5.

    Found the...
  11. Replies
    10
    Views
    6,081

    Ok! thanks

    Ok! thanks
  12. Replies
    10
    Views
    6,081

    joecar The conversion from a developed HP Tuners...

    joecar
    The conversion from a developed HP Tuners operating system to a 1290005 operating system both on 98 and E85 was not straight forward, however was well worth doing with the benefits 1290005...
  13. Replies
    13
    Views
    8,029

    Was that using the manual transmission shift...

    Was that using the manual transmission shift light settings in the tune (given the turbo 400) or was it being driven by some other means?
  14. Replies
    13
    Views
    8,029

    20443 Maybe pin 4 instead of 36?

    20443
    Maybe pin 4 instead of 36?
  15. Replies
    13
    Views
    8,029

    Tried all the settings this did not work either!

    Tried all the settings this did not work either!
  16. Replies
    13
    Views
    8,029

    Interesting!.....I will try it and report back...

    Interesting!.....I will try it and report back thanks.
  17. Replies
    13
    Views
    8,029

    Thanks for the reply I have already set...

    Thanks for the reply I have already set G1206/G1207
    Also
    B0201
    B0202
    B0203
    B0204
    B0205
    B0206
    B0207
    have been addressed.
  18. Replies
    13
    Views
    8,029

    PCM driven shift light on an auto

    I am using 01290005 operating system and trying to use the air pump output pin red plug pin 36 to drive a shift light at a programmed RPM.
    Activated air pump in the platform and adjusted the setting...
  19. Replies
    10
    Views
    6,081

    Certainly a reply with a lot of detailed...

    Certainly a reply with a lot of detailed information thank you for the effort and time you put into replying.
    I should be able to confidently make the conversion now.
    Excellent support light years...
  20. Replies
    10
    Views
    6,081

    Joe, thanks for the prompt response. I am...

    Joe, thanks for the prompt response. I am converting a developed 2bar VCM Suite tune to 1290005 transfering all setting across to EFI Live 1290005 operating system, in particular for the extended...
  21. Replies
    10
    Views
    6,081

    1290005 with LTFT

    Can I run 1290005 custom operating system on an LS1 using B3647 and still have the LTFT active by having standard settings in B4205 and having B4108 enabled?
    Or does this operating system only...
  22. Joecar and Blacky thank you for the high level of...

    Joecar and Blacky thank you for the high level of support for this issue, a credit to the EFI Live product.
    I now have a better understanding of what is required and if something goes wrong I am...
  23. Thanks for that link, after reading the...

    Thanks for that link, after reading the instructions to upgrade it is obvious that it would be very easy to get into trouble.
    I have four questions.
    (1) It has been indicated this should be done...
  24. Thank you for the prompt response. My V2...

    Thank you for the prompt response.
    My V2 firmware version is 2.4.65
    "edit the config for your PCM (if not already done)," is there a link any where that explains how to do this?
  25. All a little bit confusing this! I am trying to...

    All a little bit confusing this! I am trying to update to the v8 software as it has been indicated this should be done even when using V7 software
    I am currently running V7 software 7.5.7 build 211...
Results 1 to 25 of 50
Page 1 of 2 1 2