Results 1 to 7 of 7

Thread: LC-1 free air calibration from FlashScan V2

  1. #1
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default LC-1 free air calibration from FlashScan V2

    First, do heater cal (if you haven't already):
    - remove sensor from LC-1 module and power up for a few seconds, then power off;
    - insert sensor into LC-1 module and power up again.
    If you ever replace the sensor, you have to do this again.


    Update V2 firmware/bootblock:
    Make sure you have updated the V2 bootblock to latest and firmware to latest..

    Configure V2:
    On the V2 LCD/keypad go F4 Options->F1 Setup->F1 Edit Settings and set the following:
    Ser PIDs -> YES
    COM Port -> Wideband
    WO2 Type -> Innovate
    WO2 Format -> Both
    WO2 Data -> AFR & EQ

    Do free air cal (repeat occassionally):
    -
    make sure sensor is in free air (engine has been off overnight, or expose sensor to air);
    - on V2 menu, go F2 Scan Tool->F1 Data Logging->F3 Display WO2 and select the controller;
    - press the power button (circle with vertical bar, overlays the zero key),
    - it asks "Do free air calibration?", you answer Yes.

    Last edited by joecar; November 28th, 2011 at 09:20 AM.

  2. #2
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default Awesome thread.

    512k RoadRunner Firmware 12.14R
    FlashScan V2 Bootblock V2.07.04 Firmware V2.07.22 EFILive V7.5.7 (Build 191) V8.2.1 (Build 181)
    LC-1 WBO2

    _________________________________________________

  3. #3
    Lifetime Member 98 tigershark's Avatar
    Join Date
    Nov 2006
    Posts
    304

    Default That is very good info,

    Hey Joe,

    Thank you for that info. That is a very good post!!
    Thanks,
    98 tigershark
    98 tigershark
    L92/427 w/L76 CC'ed heads n upgraded springs
    4.100 stroke, 4.068 bore w/ 11:1 comp
    Cam, 591 int, 613exhst, 232-246dur@.050, 115*
    LG headers, High flow cats,
    RPM level 5 trans, RPM 3.42 gears, 2800 rpm trq convrt. .
    Special Thanx to Joe and Bruce!

  4. #4
    Lifetime Member
    Join Date
    Aug 2007
    Posts
    222

    Default

    Quote Originally Posted by joecar View Post
    First, do heater cal (if you haven't already):
    - remove sensor from LC-1 module and power up for a few seconds, then power off;
    - insert sensor into LC-1 module and power up again.
    If you ever replace the sensor, you have to do this again.


    Update V2 firmware/bootblock:
    Make sure you have updated the V2 bootblock to 2.06.02 and firmware to 2.06.06...

    Configure V2:
    On the V2 LCD/keypad go F4 Options->F1 Setup->F1 Edit Settings and set the following:
    Ser PIDs -> YES
    COM In -> Wide-O2
    COM Out -> Wide-O2
    WO2 Type -> Innovate
    WO2 Format -> Both
    WO2 Data -> AFR & EQ

    Do free air cal (repeat occassionally):
    -
    make sure sensor is in free air (engine has been off overnight, or expose sensor to air);
    - on V2 menu, go F2 Scan Tool->F1 Data Logging->F3 Display WO2 and select the controller;
    - press the power button (circle with vertical bar, overlays the zero key),
    - it asks "Do free air calibration?", you answer Yes.


    Where you say ser pids YES ... My v2 says no and I cannot seem to get it to say yes.
    00 GMC,LQ4, Jarrett Faggart pistons, callies rods, Ebay studs, LS9 gaskets, 317's, KBRacing KIT, PT76/75, treadstone intercooler,Eboost2, dual walbro, FIC 75lb, br7ef, Trutrac, Shaftmasters Shaft, 3.5" DP w/4" magnaflow dumped, turbo blanket, Circle D 3200, Jake's built 4l80w/brake, hydroboost, EFILive v2,Lunati dual springs,222/226 cam, cal-tracs, QA1 front shocks, Street/strip Bogarts,Drum swap, Alky-control,MSD8733 936 HP to the tire DD.

  5. #5
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by Slowrc View Post
    Where you say ser pids YES ... My v2 says no and I cannot seem to get it to say yes.
    Use the left arrow or right arrow to change the No to Yes; then press Enter.

  6. #6
    Lifetime Member
    Join Date
    Aug 2007
    Posts
    222

    Default

    Big THANKS to you!
    00 GMC,LQ4, Jarrett Faggart pistons, callies rods, Ebay studs, LS9 gaskets, 317's, KBRacing KIT, PT76/75, treadstone intercooler,Eboost2, dual walbro, FIC 75lb, br7ef, Trutrac, Shaftmasters Shaft, 3.5" DP w/4" magnaflow dumped, turbo blanket, Circle D 3200, Jake's built 4l80w/brake, hydroboost, EFILive v2,Lunati dual springs,222/226 cam, cal-tracs, QA1 front shocks, Street/strip Bogarts,Drum swap, Alky-control,MSD8733 936 HP to the tire DD.

  7. #7
    Junior Member
    Join Date
    Sep 2009
    Posts
    24

    Default

    Awesome! Just Awesome!

Similar Threads

  1. Faster Free Rev?
    By Wasted Income in forum Gen III V8 Specific
    Replies: 4
    Last Post: April 26th, 2010, 12:51 PM
  2. Problem with free air calibration on LC-1
    By MyM8V8 in forum General (Petrol, Gas, Ethanol)
    Replies: 3
    Last Post: March 20th, 2010, 08:15 PM
  3. LS1-A stream free?
    By joshp14 in forum FlashScan V2
    Replies: 7
    Last Post: January 10th, 2010, 07:54 AM
  4. BBL triggering Free to air CAL on LC1
    By Raven in forum Black Box Logging
    Replies: 39
    Last Post: May 30th, 2009, 05:02 AM
  5. WB free air calibration
    By caver in forum General
    Replies: 0
    Last Post: July 13th, 2006, 06:04 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •