Page 4 of 4 FirstFirst ... 234
Results 31 to 36 of 36

Thread: crank relearn??

  1. #31
    Lifetime Member Tinbender59's Avatar
    Join Date
    Jun 2010
    Posts
    289

    Default

    Ok, I've fixed the neutral safety switch, feed 12 volts to th correct pin for brake feed. Changed tune, still will not let me do crank relearn. What is the scan tool looking for, I'll start there??

  2. #32
    Lifetime Member Tinbender59's Avatar
    Join Date
    Jun 2010
    Posts
    289

    Default

    How do the guys running a stand alone harness get this done?

  3. #33
    Senior Member
    Join Date
    Jan 2010
    Posts
    165

    Default

    Vehicle needs to be within a certain temp range. Must be in Park, and see Foot applied on the brake signal. No DTC's pending.

    That's all I can recall at the moment.

  4. #34
    Junior Member
    Join Date
    Mar 2021
    Posts
    23

    Default

    An old thread, but very relevant. Trying to do a crank relearn with no luck. LS1B 2001 Camaro manual tune Operating System 12202088 on a 24x conversion Ramjet 350 . I have both the Brake and clutch switches. C1 32 Normally Closed to ground, C1 33 NC to 12v. Using Ver 8 Scan and Tune, with a V3 device. Thinking about trying Ver 7.5 Scan if that will even work with my V3. It starts, but runs rough. Throwing P0200 injector codes, P0480/P0481 fan codes along with the P1336 CKP relearn code. Clear them before relearn, still nothing. I think ill try grounding C1 34 to fake park/neutral even though it is a manual tune. Any thoughts or suggestions??? Thanks!

  5. #35
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    I'll have to look at the GM service manual to see all the required conditions.

  6. #36
    Junior Member
    Join Date
    Mar 2021
    Posts
    23

    Default

    Quote Originally Posted by joecar View Post
    I'll have to look at the GM service manual to see all the required conditions.
    That would be great. I have tried all I could think of. made sure there were no current faults, foot brake on, clutch in, grounding C1 34 P/N. still no go. I just set it to No MIL for now to deal with later. P0327 KS is kicking my ass now!

Page 4 of 4 FirstFirst ... 234

Similar Threads

  1. im having a problem with the crank relearn
    By whackem04 in forum General
    Replies: 3
    Last Post: December 17th, 2009, 04:53 AM
  2. Crank relearn not working?
    By kp in forum Gen III V8 Specific
    Replies: 9
    Last Post: March 25th, 2009, 01:14 PM
  3. E38 5.3 LMG Crank relearn
    By harascho in forum Gen IV V8 Specific
    Replies: 13
    Last Post: December 4th, 2008, 07:04 AM
  4. crank relearn
    By odd boy in forum General (Petrol, Gas, Ethanol)
    Replies: 15
    Last Post: August 28th, 2008, 05:07 AM
  5. Crank Relearn
    By mk6racer in forum Gen III V8 Specific
    Replies: 9
    Last Post: May 15th, 2008, 10:05 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •