Page 1 of 4 123 ... LastLast
Results 1 to 10 of 37

Thread: Anyway to fool 411 PCM into thinking its connected to 4L60E for TCC operation?

  1. #1
    Junior Member
    Join Date
    Oct 2008
    Posts
    30

    Default Anyway to fool 411 PCM into thinking its connected to 4L60E for TCC operation?

    I did a 411 PCM swap in an 89 camaro and I want to use the PCM to control the TCC on a 700R4. I have the TCC enable soleoid wire (pin 42) wired to the TCC lockup solenoid. I can command it to lock through the DVT page in the scanner but it wont lock by itself....anyhelp?

  2. #2
    Junior Member
    Join Date
    Oct 2008
    Posts
    30

    Default

    monitoring tstate9 says that the tcc is not locked due to cold transmission and due to range.

  3. #3
    Junior Member
    Join Date
    Oct 2008
    Posts
    30

    Default

    Can I put a resistor between pins on the ecm for the temp sensor...but what is the range error?

  4. #4
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Yes, you can place a ressistor, look at this table: TFT.pdf

    You may be able to place an engine ECT sensor someplace on the trans and use that (the ECT seems to have the same temperature-vs-resistance transfer function as the TFT sensor).
    Last edited by joecar; July 25th, 2010 at 08:14 AM.

  5. #5
    Junior Member
    Join Date
    Oct 2008
    Posts
    30

    Default

    Joe I still get the tcc off due to range..what is this? I placed a resistor and the tcc off due to temp is off now..

  6. #6
    Junior Member
    Join Date
    Oct 2008
    Posts
    30

    Default

    I believe it has to due with pins c1-32, c1-34, c1-72, c2-62. In the harness 32 and 34 are connected to my shift lever switch which grounds them in park/neutral. What is needed for pins 72 and 62?

  7. #7
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Do you provide a VSS signal to the PCM...?

  8. #8
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    You maybe do need:
    - P/N Position switch input (C1-34),
    - TCC Brake switch position input (C1-33),
    - Manual Valve Pressure switch input (C1-17,18, C2-63).

    In my schematic, C1-32 is Clutch Pedal Position (i.e. manual trans)...?

  9. #9
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    I don't see c1-72, c2-62...

    what vehicle/year/model schematic/harness are you using...?

  10. #10
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by slow89irocz View Post
    Joe I still get the tcc off due to range..what is this? I placed a resistor and the tcc off due to temp is off now..
    The word range refers to the range indicated by the manual valve position pressure switches (3 or 4 switches depended on car/truck application).

Page 1 of 4 123 ... LastLast

Similar Threads

  1. 4L60E, Yank 3600 Stall, 3.42 gears TCC Apply/Release
    By 1fastgto in forum 4speed RWD/FWD Transmission Tuning (incl T42)
    Replies: 20
    Last Post: February 1st, 2010, 05:00 AM
  2. pcm swap any 411 will work?
    By pullincrazy88 in forum Vortec V6/V8 Specific
    Replies: 1
    Last Post: May 25th, 2009, 10:30 PM
  3. TCC slipage on 4l60e
    By baughauto in forum 4speed RWD/FWD Transmission Tuning (incl T42)
    Replies: 0
    Last Post: May 14th, 2009, 04:03 AM
  4. 97 yukon, 411, 4l60e
    By W_D_R in forum 4speed RWD/FWD Transmission Tuning (incl T42)
    Replies: 5
    Last Post: October 17th, 2008, 04:23 AM
  5. 411 PCM's
    By joecar in forum Lounge
    Replies: 4
    Last Post: June 4th, 2007, 10:07 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •