Page 1 of 4 123 ... LastLast
Results 1 to 10 of 31

Thread: Response $31: "Request Out of Range" when changing VIN on '00 Escalade

  1. January 19th, 2011 #1
    mjalstad
    mjalstad is offline
    Junior Member
    Join Date
    Jan 2011
    Posts
    12

    Default Response $31: "Request Out of Range" when changing VIN on '00 Escalade

    So all I'm trying to do is change the VIN on a '00 Escalade PCM but I'm getting this response $31 error. I changed many VIN on many 99-08 LS1 PCMs ('01 Tahoe, '02 Silverado, '05 Silverado) and never had a problem but now this 98-00 Vortec PCM connects and seems to be all good and can read the PCM's current VIN but when I try to change it I get the error. Here's the error report:


    Error report generated by EFILive at 23:09:19 on Jan 19, 2011

    Error code: ERR_RESPONSE/5
    Response $31: "Request Out of Range".

    EFILive Version: 7.5.6 (Build 133)

    Platform: Windows NT
    Version: 6.0 (build 6002)
    Processor type: Pentium 2600MHz

    Directories
    Temporary Cache: C:\Users\Matt\Documents\EFILive\V7.5\Temporary cache
    Logged Data: C:\Users\Matt\Documents\EFILive\V7.5\Logged data
    Customers: C:\Users\Matt\Documents\EFILive\V7.5\Customers
    Configuration: C:\Program Files\EFILive\V7.5\Configuration
    Exported Data: C:\Users\Matt\Documents\EFILive\V7.5\Exported data
    Images: C:\Users\Matt\Documents\EFILive\V7.5\Images
    Sounds: C:\Users\Matt\Documents\EFILive\V7.5\Sounds
    Maps: C:\Users\Matt\Documents\EFILive\V7.5\Maps
    Pids: C:\Users\Matt\Documents\EFILive\V7.5\PIDs
    Virtual Dash: C:\Users\Matt\Documents\EFILive\V7.5\VDash
    Print Reports: C:\Users\Matt\Documents\EFILive\V7.5\Print reports
    Bug Reports: C:\Users\Matt\Documents\EFILive\V7.5\Bug reports

    Connected: No
    Com port: 0
    Com setup: EFILive FlashScan V2.5: USB
    Requested baud rate: 115200

    Cable id: 7
    Cable code: FlashScan V2
    Cable desc: EFILive FlashScan V2
    Cable version: 2.6.12
    Cable Firmware date: 20090607
    Cable model: FSV2
    Cable Serial number: 003823256641

    Protocols: 0
    Protocol list:

    Auto connect: No
    Scan OBDII info: No

    Error retries: 1
    Retry delay: 10
    Message throttle: 0

    Most recently used VIN: 1GYEK13R1YRxxxxxx (Note: 1)

    PCM information
    Hardware Number: N/A
    Calibration ID: Unknown
    Serial Number: 40EYK3928186
    Operating System: 16265175
    Engine Calibration: 16259044
    Not used: 16259128
    Transmission Calibration: 16259128
    Not used: 16259197
    Fuel System: 16259197
    System: 16259247
    Speedometer: 16241186
    Operating System BCC: CDNH
    Stream-Slow scan mode: Supported
    Stream-Fast scan mode: Supported
    Maximum dynamic packets: 16

    Detected modules:
    $10="Powertrain Control Module (PCM)"


    Report ID: 1933831 (Note: 2)

    Notes:
    (1) The VIN sequence number is not required for this report and for your privacy it is NOT included in this report.

    (2)The report ID is a checksum of the report text and is used to verify the integrity of the report.
    Reply With Quote Reply With Quote
  2. January 19th, 2011 #2
    Tordne
    Tordne is offline
    EFILive Crew Site Admin Tordne's Avatar
    Join Date
    Oct 2004
    Posts
    3,870

    Default

    Please update both your software and firmware versions and try again.

    Here are a couple of knowledgebase articles relating to software and firmware updates:
    - Software
    - Firmware
    Andrew
    EFILive Crew

    Reply With Quote Reply With Quote
  3. January 20th, 2011 #3
    mjalstad
    mjalstad is offline
    Junior Member
    Join Date
    Jan 2011
    Posts
    12

    Default

    Still didn't work

    Error report generated by EFILive at 06:53:07 on Jan 20, 2011

    Error code: ERR_RESPONSE/5
    Response $31: "Request Out of Range".

    EFILive Version: 7.5.6 (Build 133)

    Platform: Windows NT
    Version: 6.0 (build 6002)
    Processor type: Pentium 2600MHz

    Directories
    Temporary Cache: C:\Users\Matt\Documents\EFILive\V7.5\Temporary cache
    Logged Data: C:\Users\Matt\Documents\EFILive\V7.5\Logged data
    Customers: C:\Users\Matt\Documents\EFILive\V7.5\Customers
    Configuration: C:\Program Files\EFILive\V7.5\Configuration
    Exported Data: C:\Users\Matt\Documents\EFILive\V7.5\Exported data
    Images: C:\Users\Matt\Documents\EFILive\V7.5\Images
    Sounds: C:\Users\Matt\Documents\EFILive\V7.5\Sounds
    Maps: C:\Users\Matt\Documents\EFILive\V7.5\Maps
    Pids: C:\Users\Matt\Documents\EFILive\V7.5\PIDs
    Virtual Dash: C:\Users\Matt\Documents\EFILive\V7.5\VDash
    Print Reports: C:\Users\Matt\Documents\EFILive\V7.5\Print reports
    Bug Reports: C:\Users\Matt\Documents\EFILive\V7.5\Bug reports

    Connected: No
    Com port: 0
    Com setup: EFILive FlashScan V2.5: USB
    Requested baud rate: 115200

    Cable id: 7
    Cable code: FlashScan V2
    Cable desc: EFILive FlashScan V2
    Cable version: 2.7.4
    Cable Firmware date: 20101130
    Cable model: FSV2
    Cable Serial number: 003823256641

    Protocols: 0
    Protocol list:

    Auto connect: No
    Scan OBDII info: No

    Error retries: 1
    Retry delay: 10
    Message throttle: 0

    Most recently used VIN: 1GYEK13R1YRxxxxxx (Note: 1)

    PCM information
    Hardware Number: N/A
    Calibration ID: Unknown
    Serial Number: 40EYK3928186
    Operating System: 16265175
    Engine Calibration: 16259044
    Not used: 16259128
    Transmission Calibration: 16259128
    Not used: 16259197
    Fuel System: 16259197
    System: 16259247
    Speedometer: 16241186
    Operating System BCC: CDNH
    Stream-Slow scan mode: Supported
    Stream-Fast scan mode: Supported
    Maximum dynamic packets: 16

    Detected modules:
    $10="Powertrain Control Module (PCM)"
    Reply With Quote Reply With Quote
  4. January 20th, 2011 #4
    Tordne
    Tordne is offline
    EFILive Crew Site Admin Tordne's Avatar
    Join Date
    Oct 2004
    Posts
    3,870

    Default

    Your V7 software hasn't been updated, it is still showing version 133. Could you please try and install the Build 139 version on our website?

    Are you able to scan/datalog the vehicle at all?
    Andrew
    EFILive Crew

    Reply With Quote Reply With Quote
  5. January 20th, 2011 #5
    mjalstad
    mjalstad is offline
    Junior Member
    Join Date
    Jan 2011
    Posts
    12

    Default

    Ok I got that updated and still the same thing. I am doing this on a benchtop with a wiring harness from EFIconnection.com. I have never done any scanning or datalogging and I don't even know if I would be able to do that since the PCM is out of the vehicle. When I click on the change vin option, it is able to read the PCM's current VIN and puts that in the "Current VIN" field. Even if I clikc on "copy VIN" and "check Digit" then "ok" it still comes up with this error.

    Error report generated by EFILive at 21:28:21 on Jan 20, 2011

    Error code: ERR_RESPONSE/5
    Response $31: "Request Out of Range".

    EFILive Version: 7.5.6 (Build 139)

    Platform: Windows NT
    Version: 6.0 (build 6002)
    Processor type: Pentium 2600MHz

    Directories
    Temporary Cache: C:\Users\Matt\Documents\EFILive\V7.5\Temporary cache
    Logged Data: C:\Users\Matt\Documents\EFILive\V7.5\Logged data
    Customers: C:\Users\Matt\Documents\EFILive\V7.5\Customers
    Configuration: C:\Program Files\EFILive\V7.5\Configuration
    Exported Data: C:\Users\Matt\Documents\EFILive\V7.5\Exported data
    Images: C:\Users\Matt\Documents\EFILive\V7.5\Images
    Sounds: C:\Users\Matt\Documents\EFILive\V7.5\Sounds
    Maps: C:\Users\Matt\Documents\EFILive\V7.5\Maps
    Pids: C:\Users\Matt\Documents\EFILive\V7.5\PIDs
    Virtual Dash: C:\Users\Matt\Documents\EFILive\V7.5\VDash
    Print Reports: C:\Users\Matt\Documents\EFILive\V7.5\Print reports
    Bug Reports: C:\Users\Matt\Documents\EFILive\V7.5\Bug reports

    Connected: No
    Com port: 0
    Com setup: EFILive FlashScan V2.5: USB
    Requested baud rate: 115200

    Cable id: 7
    Cable code: FlashScan V2
    Cable desc: EFILive FlashScan V2
    Cable version: 2.7.4
    Cable Firmware date: 20101130
    Cable model: FSV2
    Cable Serial number: 003823256641

    Protocols: 0
    Protocol list:

    Auto connect: No
    Scan OBDII info: No

    Error retries: 1
    Retry delay: 10
    Message throttle: 0

    Most recently used VIN: 1GYEK13R1YRxxxxxx (Note: 1)

    PCM information
    Hardware Number: N/A
    Calibration ID: Unknown
    Serial Number: 40EYK3928186
    Operating System: 16265175
    Engine Calibration: 16259044
    Not used: 16259128
    Transmission Calibration: 16259128
    Not used: 16259197
    Fuel System: 16259197
    System: 16259247
    Speedometer: 16241186
    Operating System BCC: CDNH
    Stream-Slow scan mode: Supported
    Stream-Fast scan mode: Supported
    Maximum dynamic packets: 16

    Detected modules:
    $10="Powertrain Control Module (PCM)"
    Reply With Quote Reply With Quote
  6. January 20th, 2011 #6
    mjalstad
    mjalstad is offline
    Junior Member
    Join Date
    Jan 2011
    Posts
    12

    Default

    Ok so I just tried scanning which I have never done before. Since the PCM is out of the vehicle I just checked the battery voltage PID and it scans and comes up at 12.0 so I would have to say that yes, I am able to scan.
    Reply With Quote Reply With Quote
  7. January 21st, 2011 #7
    Blacky
    Blacky is offline
    EFILive Developer Site Admin Blacky's Avatar
    Join Date
    Mar 2003
    Posts
    9,500

    Default

    When you posted the error reports, there should have been a whole lot of extra data that is not present in the ones that you posted. Can you post the entire error report after you get the error when trying to save the VIN.
    Regards
    Paul
    Before asking for help, please read this.
    Reply With Quote Reply With Quote
  8. January 21st, 2011 #8
    Blacky
    Blacky is offline
    EFILive Developer Site Admin Blacky's Avatar
    Join Date
    Mar 2003
    Posts
    9,500

    Default

    Use the [Save] button when the error report shows up, then attach the saved file to your post.
    To attach the file, click the [Go Advanced] button underneath your post.
    Then click the [Manage attachments] button to upload the file as an attachment.

    Regards
    Paul
    Before asking for help, please read this.
    Reply With Quote Reply With Quote
  9. January 21st, 2011 #9
    mjalstad
    mjalstad is offline
    Junior Member
    Join Date
    Jan 2011
    Posts
    12

    Default

    There we go, I guess that is probably a little easier, haha
    Attached Files Attached Files
    Reply With Quote Reply With Quote
  10. January 27th, 2011 #10
    mjalstad
    mjalstad is offline
    Junior Member
    Join Date
    Jan 2011
    Posts
    12

    Default

    Any ideas yet?
    Reply With Quote Reply With Quote
Page 1 of 4 123 ... LastLast
« Previous Thread | Next Thread »

Similar Threads

  1. EFILive "Classic"/"Legacy"/"Historic"?
    By emarkay in forum FlashScan V2
    Replies: 6
    Last Post: November 2nd, 2008, 02:48 AM
  2. 12200411 retrofit, have efilive "VIN" question
    By rb1 in forum Gen III V8 Specific
    Replies: 2
    Last Post: June 2nd, 2007, 07:39 AM
  3. "PCM is in an Unkown State" & "Reflash Failed"
    By foxySS in forum General (Petrol, Gas, Ethanol)
    Replies: 5
    Last Post: September 8th, 2006, 12:53 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules