Page 1 of 2 12 LastLast
Results 1 to 10 of 18

Thread: GEN IV E38 Holden Commodore Cooling Fans

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    New Member
    Join Date
    Feb 2011
    Posts
    9

    Question GEN IV E38 Holden Commodore Cooling Fans

    Hi Forum,
    New guy here who needs advice. I've just transplanted an L98 into a Nissan Patrol and am running a dedicated wiring harness with an E38 from a VZ Commodore with the VATS removed.

    Problem is I cannot get the cooling fans to operate when the coolant temp gets to the preset level. The fans are set to 'Discrete' in EFILIVE and the high and low speed fan relay drive wires are connected to pins 17 and 58 of the E38 respectively.

    Any advice?

  2. #2
    Lifetime Member
    Join Date
    Aug 2010
    Posts
    1,934

    Default

    Hello CRFaig,

    What OS is your E38 running ?

    Did you apply the “Cooling Fan Operation Range Patch” (B9904) ? You won’t see this patch unless you have the V2 connected to your Laptop prior to opening the tune file.


    Regards,
    Taz

  3. #3
    New Member
    Join Date
    Feb 2011
    Posts
    9

    Default

    Thanks Taz,

    Firstly, it's great to see a Canuck with an Aussie nickname.
    Ok, I don't currently have efilive at my disposal but the E38 has been flashed using it. So, I don't know the the operating system my E38 has.
    The supplier gave me a new E38 and now I have the low speed fans operating........Immediately after start-up and they stay on. High speed fans will not come on. I don't know if the supplier is using V2 and don't know if they have applied the B9904 patch. It's one of those situations where I don't want to tell them what they should be doing until I'm fully informed.

  4. #4
    Lifetime Member
    Join Date
    Dec 2007
    Posts
    1,143

    Default

    B9904 wont make any difference. Whoever disabled your VATS could have fixed this for you. If they didnt, then maybe there are some other revisions required too. When we set an ECM up for a conversion we supply a calibration that has all the revisions for a conversion. Your tuner appears to be using EFILive, so they can fix the problem .
    Last edited by gmh308; February 12th, 2011 at 10:39 PM.

  5. #5
    New Member
    Join Date
    Dec 2010
    Posts
    7

    Default

    Hey mate, who did the conversion? and how much roughly? Always wanted an L98 in a patrol.

  6. #6
    New Member
    Join Date
    Feb 2011
    Posts
    9

    Default

    Hey DMAX,

    The conversion fit was done by myself with the parts kit and engine supplied by Marks 4WD in Dandenong, Victoria.

    Cost............Including everything aside from labour, the bill is up to approx $23000.

  7. #7
    New Member
    Join Date
    Dec 2010
    Posts
    7

    Default

    Are you a member of the Patrol forum? Would love to see pics of it all. I was going to go with the same engine before I went with a Duramax/allison combo, but still love me ls motors.

  8. #8
    New Member
    Join Date
    Feb 2011
    Posts
    9

    Default

    Not a member but it could be good to upload some pics. Will wait to all is finished; i.e. the cooling fans work as they should, the A/C is functional and the exhaust is corrected after the engineers goes through.

    Still at a loss with the cooling fans........

  9. #9
    Senior Member doubledip's Avatar
    Join Date
    May 2008
    Posts
    163

    Default

    take it to Mark's 4x4 he should fix it if you bought the kit off him - its an easy fix
    ---------------------------
    E38's got to love them
    E40's hate 'em

    LS1's is there anything it wont work on

    Holden VE SSV - GEN46L

    www.ultimateconversionwiring.com.au

    www.dualflash.com.au

  10. #10
    New Member
    Join Date
    Feb 2011
    Posts
    9

    Default

    Thanks Doubledip.

    Yes, has been back to Marks (or at least the ECU's have) It's on its fourth ECU. The first one didn't drive the fans at all. No ground and faulty. The second made the fans come on low speed straight after start-up. Mark reprogrammed another ECU with the percentages changed in the fan control parameters and we did the swap over. Put it in, no start and no tester communication. Swapped it over for another ECU and everything works but, as before, the fans come on immediately after start-up.
    Mark has been really helpful with the ECU probs (came into his work on Saturday to swap over the dodgy ECU) and let me know that it looks like he's had a small run of faulty remanufactured E38's.

    So....I've heard it's an easy fix. I've also been told that an EFILIVE reprogrammed E38 cannot run low and high speed as per the factory tune.

    Is this true?

Page 1 of 2 12 LastLast

Similar Threads

  1. Holden Commodore VR Buick 3.8 V6 Tune?
    By strongarmz in forum General (Petrol, Gas, Ethanol)
    Replies: 7
    Last Post: August 16th, 2011, 01:02 PM
  2. E38 pwm cooling fan control
    By vette5797 in forum Conversions / Aftermarket Parts
    Replies: 1
    Last Post: December 24th, 2009, 05:07 AM
  3. E38 Cooling fans question
    By Chalky in forum E37, E38 & E67 PFI ECM's
    Replies: 2
    Last Post: September 1st, 2009, 01:11 PM
  4. Holden VE Commodore Engineering Mode
    By Blacky in forum Lounge
    Replies: 2
    Last Post: June 4th, 2009, 08:19 PM
  5. 2002 Holden Commodore spark scaler problems
    By caver in forum General (Petrol, Gas, Ethanol)
    Replies: 4
    Last Post: December 9th, 2005, 07:25 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •