Page 8 of 9 FirstFirst ... 6789 LastLast
Results 71 to 80 of 84

Thread: Calc.MAFT: correcting VE and calculating MAF (in single log) --> reverse of Calc.VET

  1. #71
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by CHEVYHD496 View Post
    Ok, please go easy on me as I'm new to this! When you say "disable maf", how do I disable it? Then I do not have a WBO2, so can I then still use this setup to tune? Thanks!
    Disable the MAF by causing a MAF DTC to immediately show up...

    this can be done in any one of these ways:
    - unplug MAF if you have 3-wire connector (i.e. IAT is on separate connector).
    - edit C2901-3 to force MAF to fail.

    You may have to edit C6001 to cause P0101-3 to trigger on 1-Trip.

    If you don't have a wideband then you will only be able to correct VE for Closed Loop, i.e. low/light throttle only.

    ~ posted by phone ~

  2. #72
    Lifetime Member
    Join Date
    Feb 2016
    Posts
    243

    Default

    Can this be done without a wideband O2 sensor?

  3. #73
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by oreobadr View Post
    Can this be done without a wideband O2 sensor?
    Without a wideband, you can do only CL (meaning light throttle), so you won't be able to reach high into the upper MAF table and upper VE table.

  4. #74
    Member
    Join Date
    Oct 2005
    Posts
    86

    Default

    Quote Originally Posted by WeathermanShawn View Post
    In-Memory-of-Shawn-Sankey
    5. Paste-with-labels the new CALC.MAFT map into Table B5001 in your tune file:

    ( ignore this step if you're running SD, i.e. ignoring MAF and doing VE table only )



    (to limit the cell display width to something sensible, in the map properties goto the Cell tab and look at Constrain Cell Size)
    Can't find a CALC.MAFT map. What is the data in the Value column above?

  5. #75
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by voda1 View Post
    Can't find a CALC.MAFT map.
    see attached zips for maps.

    What is the data in the Value column above?
    For the MAF map, the Column pid can be any pid you logged... for convenience I make it GM.MAFFREQ (same as the Row pid).
    Attached Files Attached Files

  6. #76
    Member
    Join Date
    Nov 2009
    Posts
    79

    Default

    Can someone please provide the necessary pids because the pictures on the first post are gone. Thanks

  7. #77
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Hmmm, I hate when PhotoBucket does that.

    Look in the calc_pids.txt file, log all the pids mentioned in there.

    There's a pdf of Calc.VET procedure here somewhere, let me find it.

  8. #78
    Senior Member
    Join Date
    May 2014
    Posts
    125

    Default

    Quote Originally Posted by joecar View Post
    Hmmm, I hate when PhotoBucket does that.

    Look in the calc_pids.txt file, log all the pids mentioned in there.

    There's a pdf of Calc.VET procedure here somewhere, let me find it.
    Joe, here are the 4 pics in the OP without the photobucket watermark nonsense. Use them to update the OP if you'd like and I think it would be wise to host them directly on the website so it's not reliant on an external source. I'll do the same in the VET thread.

    https://i.imgur.com/StdYwMe.png
    https://i.imgur.com/vR2YyoO.png
    https://i.imgur.com/17Ml0Ab.png
    https://i.imgur.com/wEzVfSW.png

  9. #79
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    I'll look over the next few days.

  10. #80
    Junior Member
    Join Date
    Nov 2009
    Posts
    26

    Default

    I'm glad you guys have the pics. I'm going over this to try to set up to tune. I finally have my WB up and running. I want tot data log now and start the process.
    Thank you!!
    Doing my best to fix what ain't broke!!

Page 8 of 9 FirstFirst ... 6789 LastLast

Similar Threads

  1. Calc.VET: correcting MAF and calculating VE (in single log)
    By WeathermanShawn in forum Gen III V8 Specific
    Replies: 742
    Last Post: February 20th, 2023, 03:55 AM
  2. CALC VET Summary Notes
    By WeathermanShawn in forum Gen III V8 Specific
    Replies: 32
    Last Post: August 28th, 2014, 06:49 PM
  3. CALC. VE Table help
    By nchristian in forum Gen III V8 Specific
    Replies: 1
    Last Post: January 28th, 2011, 08:18 AM
  4. RPM Threshold for Airflow Calc {B0120}:
    By Mark300 in forum E37, E38 & E67 PFI ECM's
    Replies: 3
    Last Post: December 2nd, 2009, 12:40 PM
  5. Startup Friction Airflow Correction table?
    By jnorris in forum General (Petrol, Gas, Ethanol)
    Replies: 5
    Last Post: November 10th, 2005, 04:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •