Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: 12620015 support for DSP-LMM

  1. #1
    Lifetime Member killerbee's Avatar
    Join Date
    Jan 2006
    Posts
    1,079

    Default 12620015 support for DSP-LMM

    Does it exist? I get the "unsupported" message after doing the dsp5 upgrade.\
    This is a 4500-5500 truck.
    Michael, Systems Engineer 04.5 D-max LLY, Phoenix, Arizona Email
    Custom Tuning Services
    DURAMAX/CUMMINS ECM's TCM's for sale, all years, 20% wholesale discount available
    EFILive's first VGT "Software Wastegate Tune"

  2. #2
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Sorry, it doesn't exist. If I recall there was something odd about that particular OS that made it impossible to perform the DSP mods to. It is non standard compared to all other Bosch Duramax OS's.
    I no longer monitor the forum, please either post your question or create a support ticket.

  3. #3
    Lifetime Member killerbee's Avatar
    Join Date
    Jan 2006
    Posts
    1,079

    Default

    I wonder then, what happens when you put a LD os in a MD truck (LMM).
    Michael, Systems Engineer 04.5 D-max LLY, Phoenix, Arizona Email
    Custom Tuning Services
    DURAMAX/CUMMINS ECM's TCM's for sale, all years, 20% wholesale discount available
    EFILive's first VGT "Software Wastegate Tune"

  4. #4
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    I'm not sure, but 12617083 was the OS release prior to the oddball MD, that might be your best bet.
    I no longer monitor the forum, please either post your question or create a support ticket.

  5. #5
    New Member
    Join Date
    Nov 2017
    Posts
    8

    Default

    Quote Originally Posted by GMPX View Post
    I'm not sure, but 12617083 was the OS release prior to the oddball MD, that might be your best bet.
    Just woundering if anyone has tried using a light truck operating system in a kodiak with os 12620015 would like to have the dsp5 but seems it might not be doable.thx

  6. #6
    Lifetime Member GMC-2002-Dmax's Avatar
    Join Date
    Dec 2005
    Posts
    1,294

    Default

    NOPE, will not work, results in a dead key, no crank
    www.mscservices.net


    Tuner of many, many Duramax and Cummins Diesels.


  7. #7
    New Member
    Join Date
    Nov 2017
    Posts
    8

    Default

    Is there any other os that could be flashed over os 12620015 one this 2008 kodiak thx

  8. #8
    Lifetime Member GMC-2002-Dmax's Avatar
    Join Date
    Dec 2005
    Posts
    1,294

    Default

    Quote Originally Posted by Tyson View Post
    Is there any other os that could be flashed over os 12620015 one this 2008 kodiak thx
    Nope, any VAN or Kodiak will not work at all with a Pickup single or DSP2 or DSP5 tune.

    You have to use correct OS for that Kodiak Only single tunes only.

    It just will not work
    Last edited by GMC-2002-Dmax; February 25th, 2019 at 06:51 AM.
    www.mscservices.net


    Tuner of many, many Duramax and Cummins Diesels.


  9. #9
    Lifetime Member DURAtotheMAX's Avatar
    Join Date
    Nov 2005
    Posts
    1,016

    Default

    Its simply because the starter relay control is wired differently on the GMT-560 (kodiak) and GMT-610 (van).

    Pickup cals are setup to use a high side driver in the ECM (mapped to pin XYZ on one of the ECM connectors) to apply 12v to the coil of the starter relay. Kodiak/van use a low side driver (mapped to a different pin) to apply ground to the coil of the starter relay.

    Change some wires around in the harness, OR poke around in the ECM binary (to tell it which starter relay hardware config to use) and it should be easy to make a pickup OS work in a kodiak....
    2005 Silverado, CC/SB, 4x4, LT, LILLY/Allison
    12.9s @ 108 mph

    many thanks to Ross and Paul

  10. #10
    Lifetime Member THEFERMANATOR's Avatar
    Join Date
    Mar 2009
    Posts
    800

    Default

    Quote Originally Posted by DURAtotheMAX View Post
    Its simply because the starter relay control is wired differently on the GMT-560 (kodiak) and GMT-610 (van).

    Pickup cals are setup to use a high side driver in the ECM (mapped to pin XYZ on one of the ECM connectors) to apply 12v to the coil of the starter relay. Kodiak/van use a low side driver (mapped to a different pin) to apply ground to the coil of the starter relay.

    Change some wires around in the harness, OR poke around in the ECM binary (to tell it which starter relay hardware config to use) and it should be easy to make a pickup OS work in a kodiak....
    I believe Josh said he did just this with the dumpster van so he could run DSP5 on it.
    1995 GMC 2500 SUBURBAN powered by 01 DURAMAX/ALLISON, little of this, a little of that,
    DIAMONDEYE 4" exhaust, CORSA muffler, AFE stage 1 dry filter, custom tuning by me, KENNEDY single pump and pump rub kit.

Page 1 of 2 12 LastLast

Similar Threads

  1. DSP for LMM and LBZ
    By johnasara in forum General (Diesel)
    Replies: 8
    Last Post: December 23rd, 2009, 02:31 AM
  2. LMM DSP Beta1 Release
    By GMPX in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 51
    Last Post: December 19th, 2009, 10:20 AM
  3. LMM DSP switch
    By GL4662 in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 1
    Last Post: November 19th, 2009, 07:32 AM
  4. DSP-5 for LMM???
    By flyguy_17 in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 1
    Last Post: November 15th, 2008, 05:42 AM
  5. 2008 LMM support?
    By Boost in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 10
    Last Post: October 9th, 2007, 10:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •