Page 7 of 7 FirstFirst ... 567
Results 61 to 70 of 70

Thread: Problem logging SAE.MAP pid

  1. #61
    Senior Member
    Join Date
    Feb 2014
    Posts
    186

    Default

    yes i did thank you, but I think the RTACS is fighting the STFT fixer due to the constant changes , on that note , one of the new blowers is on and i keep getting different changes everyday, which may be the blower breaking in , but i purposely, lowered my whole ve 15 percent to see how the changes were being made and found that when i am making changes especially between 1800-2200 rpm high gear when RATCS is done my converter slips when i let off the pedal raising the rpm to 3000 ???? stock trans values and everything is ok before the changes cant figure that one out

    thanksjoe

    Jim

    Edit , this unit uses a PRV that closes at 1500 rpm and opens when the tps is lowered
    Last edited by SW1911; September 3rd, 2014 at 01:21 AM.

  2. #62
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Hmmm, TCC slips when you release throttle...? Post some log files.

  3. #63
    Senior Member
    Join Date
    Feb 2014
    Posts
    186

    Default

    i will log some trans stuff tomorrow ,
    thanks joe
    get my pm?

  4. #64
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Jim, thanks for the pm

  5. #65
    Senior Member
    Join Date
    Feb 2014
    Posts
    186

    Default

    def needs work on the fueling side , but i was able to get the slip to happen about halfway through the file
    Attached Files Attached Files

  6. #66
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    I'll take a closer look later tonite...

  7. #67
    Senior Member
    Join Date
    Feb 2014
    Posts
    186

    Default

    long log , but different tune , problem starts out around frame 4k i think now tcc slip is all over the place and it was ok this morning , i was on a fine run with RTACS and the more it changed the worse it gets ,i never had this problem before ,,,attached is a fresh start this morning , im wondering if the prv is screwing things up, its open until 1500 rpm then closes until you let off the pedal as you can see in the log and the ve , not sure how to cure this and im wondering if the trans problems are linked to this , check out the table you will see what i mean

    jim
    Attached Files Attached Files
    Last edited by SW1911; September 4th, 2014 at 11:49 PM.

  8. #68
    Junior Member
    Join Date
    Jan 2013
    Posts
    12

    Default

    I know this is an old thread but can I use the calc map on a 04073003 os I added it to the cal pids but it comes up as an unsupported pid

  9. #69
    EFILive Developer Site Admin Blacky's Avatar
    Join Date
    Mar 2003
    Posts
    9,490

    Default

    Quote Originally Posted by codeman_tinck@hotmail.com View Post
    I know this is an old thread but can I use the calc map on a 04073003 os I added it to the cal pids but it comes up as an unsupported pid
    If you are using the V7 software, in the [PIDs F8] tab page, right click on the calculated PID and select "More Info...". That will tell you why EFILive thinks it is unsupported. It is usually because one or more PIDs that the calc PID uses is not selected yet. So make sure all the PIDs that are used in the calculated PID's expression are also selected and supported.

    Regards
    Paul
    Before asking for help, please read this.

  10. #70
    Junior Member
    Join Date
    Jan 2013
    Posts
    12

    Default

    Quote Originally Posted by Blacky View Post
    If you are using the V7 software, in the [PIDs F8] tab page, right click on the calculated PID and select "More Info...". That will tell you why EFILive thinks it is unsupported. It is usually because one or more PIDs that the calc PID uses is not selected yet. So make sure all the PIDs that are used in the calculated PID's expression are also selected and supported.

    Regards
    Paul
    you are correct thank you I've been opening and closing scan alot I forgot to select gm map it works as should much appreciated
    its odd I didnt have this problem with my 0411 but this will work fine

Page 7 of 7 FirstFirst ... 567

Similar Threads

  1. What is the deference between {GM.MANVAC} and {SAE.MAP}?
    By odd boy in forum General (Petrol, Gas, Ethanol)
    Replies: 1
    Last Post: April 24th, 2008, 05:37 AM
  2. GM.MANVAC vs. SAE.MAP
    By Lennart in forum General (Petrol, Gas, Ethanol)
    Replies: 1
    Last Post: May 20th, 2007, 03:32 AM
  3. Main VE doesn't match MAP.SAE
    By LSs1Power in forum General (Petrol, Gas, Ethanol)
    Replies: 10
    Last Post: January 3rd, 2007, 02:11 PM
  4. Why doesn't SAE.MAP not work? (2-bar)
    By Alvin in forum Custom Operating Systems
    Replies: 2
    Last Post: October 27th, 2006, 05:07 PM
  5. Replies: 5
    Last Post: April 27th, 2005, 12:26 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •