Results 1 to 9 of 9

Thread: 6.7L Cummins swap/transplant

  1. #1
    New Member
    Join Date
    Nov 2011
    Posts
    3

    Default 6.7L Cummins swap/transplant

    Hi guys, kinda new to the forum thing, so please bare with me?

    I am in the midst of a 6.7 Cummins swap into a GM chassis and need some help please? The motor is a 2008 out of a low mileage Ram 5500 and I do have the ECU, harness & APPS. My main concern is wiring an OBD II port so EFI will be able to communicate and whether the CAN + & CAN - wires will need to be used since I will not be using the original BCM or TCM?

    I do have a diagram that I downloaded from the Dodge site that appears to be good but could use your direction please? My concern is being able to use EFI live upon its release to tune and eliminate emissions equipment since this will be an off road NON-emission application.

    Again guys, please & Thank U for any direction/suggestions!

  2. #2
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    I dont think EFI can communicate with the C&C ECM...dont quote me, but I think its a different ECM.
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  3. #3
    Lifetime Member Dmaxink's Avatar
    Join Date
    Nov 2009
    Posts
    1,176

    Default

    It reads but will not flash
    -Kory

    I'm out of ideas? Nah trick... When in doubt, 0xFFFF it out!

    http://www.PPEI.com/

  4. #4
    Senior Member
    Join Date
    Oct 2011
    Posts
    100

    Default

    The C&C and non C&C engines are the same parts wise, right ?

    He should be able to download a non C&C image and start with that, right ?

    I'm subscribing because I'm doing a 6.7 swap as well.

  5. #5
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    Same parts...different ECM protocols.
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  6. #6
    Lifetime Member Dmaxink's Avatar
    Join Date
    Nov 2009
    Posts
    1,176

    Default

    The read has been sent to Ross :-)
    -Kory

    I'm out of ideas? Nah trick... When in doubt, 0xFFFF it out!

    http://www.PPEI.com/

  7. #7
    New Member
    Join Date
    Nov 2011
    Posts
    3

    Default

    Hi guys, don't know if this will help any, but here is the info on the ECM..... if the upload goes right!
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	6.7 ECM 1.jpg 
Views:	577 
Size:	418.4 KB 
ID:	12339  

  8. #8
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    I don't have any of my development stuff with me here on my trip, but I would expect we should be able to tune this combo no worries. The ECM type is correct (CM2100A).
    Not sure what this is all going in to, but if it's a late model GM vehicle don't expect the ECM to talk to the cluster etc, GM and Dodge CAN messages aren't the same.
    I no longer monitor the forum, please either post your question or create a support ticket.

  9. #9
    New Member
    Join Date
    Nov 2011
    Posts
    3

    Default

    The application will be a mid eighties GM 1 ton 4x4 with a manual trans. So, no other control modules are present. No dash cluster worries either, I will eventually like to eliminate all emissions! Thank you all for the help!

Similar Threads

  1. Issues with GTO 6.0 transplant Using 04-LQ4
    By 2Aspire in forum Gen IV V8 Specific
    Replies: 10
    Last Post: July 24th, 2011, 01:12 PM
  2. lq9 engine transplant
    By lq9nissan in forum Conversions / Aftermarket Parts
    Replies: 24
    Last Post: July 9th, 2011, 04:00 AM
  3. LS3 transplant / conversion
    By The Alchemist in forum Gen III V8 Specific
    Replies: 32
    Last Post: July 1st, 2010, 05:30 PM
  4. Transplant silverado problem
    By The Dirty Dutchmen in forum Gen IV V8 Specific
    Replies: 3
    Last Post: September 9th, 2009, 07:28 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •