Results 1 to 10 of 10

Thread: Trouble flashing my ECM

  1. #1
    Junior Member derrickmanx1's Avatar
    Join Date
    Mar 2011
    Posts
    13

    Default Trouble flashing my ECM

    This is what I get when I try to flash my 06 lbz




    14:40:15.694: Scanning for EFILive FlashScan V2 HAPI
    14:40:15.708: Autodetect interface ...
    14:40:15.953: Interface firmware version: 2.7.26
    14:40:15.958: Connection to [FSV2] interface is OK
    14:40:15.972: CAN-VPW Bridge Activated
    14:40:16.039: Current protocol set to: "ISO 15765 CAN"
    14:40:16.042: Autodetect ECM...
    14:40:16.170: Connection to ECM is OK
    14:40:16.181: Current protocol: "ISO 15765 CAN"
    14:40:16.394: USB driver version: 4.0.0
    14:40:16.403: USB library version: 3.1.18
    14:40:16.419: Interface firmware model: FSV2
    14:40:16.439: Interface firmware model: FSV2
    14:40:16.457: Interface firmware version: 2.7.26
    14:40:16.474: Interface firmware date: Mar 28, 2012
    14:40:16.491: FlashScan serial number: 003861434913
    14:40:16.509: FlashScan license number: 003861434913
    14:40:16.762: Getting status...
    14:40:16.988: Status: OK.
    14:40:30.903: Disconnecting ...
    14:40:31.511: CAN-VPW Bridge Deactivated
    14:40:31.519: Disconnected
    14:40:32.123: Scanning for EFILive FlashScan V2 HAPI
    14:40:32.141: Autodetect interface ...
    14:40:32.388: Interface firmware version: 2.7.26
    14:40:32.392: Connection to [FSV2] interface is OK
    14:40:32.606: USB driver version: 4.0.0
    14:40:32.611: USB library version: 3.1.18
    14:40:32.626: Interface firmware model: FSV2
    14:40:32.643: Interface firmware model: FSV2
    14:40:32.662: Interface firmware version: 2.7.26
    14:40:32.683: Interface firmware date: Mar 28, 2012
    14:40:32.700: FlashScan serial number: 003861434913
    14:40:32.717: FlashScan license number: 003861434913
    14:40:32.750: Disconnecting ...
    14:40:33.369: CAN-VPW Bridge Deactivated
    14:40:33.377: Disconnected
    14:40:33.988: Scanning for EFILive FlashScan V2 HAPI
    14:40:34.028: Autodetect interface ...
    14:40:34.267: Interface firmware version: 2.7.26
    14:40:34.275: Connection to [FSV2] interface is OK
    14:40:34.293: CAN-VPW Bridge Activated
    14:40:34.361: Current protocol set to: "ISO 15765 CAN"
    14:40:34.369: Autodetect ECM...
    14:40:34.419: Connection to ECM is OK
    14:40:34.436: Current protocol: "ISO 15765 CAN"
    14:40:34.655: USB driver version: 4.0.0
    14:40:34.663: USB library version: 3.1.18
    14:40:34.687: Interface firmware model: FSV2
    14:40:34.705: Interface firmware model: FSV2
    14:40:34.727: Interface firmware version: 2.7.26
    14:40:34.749: Interface firmware date: Mar 28, 2012
    14:40:34.771: FlashScan serial number: 003861434913
    14:40:34.794: FlashScan license number: 003861434913
    14:40:35.049: Getting status...
    14:40:35.274: Status: OK.
    14:40:36.150: Preparing ECM for reflash...
    14:40:36.197: ECM seed is: $29F8
    14:40:36.200: Unlock attempt 1 of 1
    14:40:36.348: Initializing ECM...
    14:40:37.763: Request serial number...
    14:40:38.610: Serial number: 86J624105700
    14:40:41.221: Attempting to reboot ECM... (please wait up to 8 seconds)
    14:40:42.385: ECM has booted successfully...
    14:40:43.390: Clear emisison related DTCs...
    14:40:43.434: Clear DTCs for all modules...
    14:40:45.543: Autodetect interface ...
    14:40:45.785: Interface firmware version: 2.7.26
    14:40:45.787: Connection to [FSV2] interface is OK
    14:40:45.789: Autodetect ECM...
    14:40:45.832: Connection to ECM is OK
    14:40:47.170: Reflashing completed successfully
    14:40:50.319: Done!


    The time is 35 seconds total. There is no way it's flashed. Any help would be great. It will flash my TCM no problem. All software and firmware up to date. I can't even read the ecm's tune.
    Last edited by derrickmanx1; May 6th, 2012 at 12:26 AM. Reason: info

  2. #2
    Lifetime Member THEFERMANATOR's Avatar
    Join Date
    Mar 2009
    Posts
    800

    Default

    If you are doing a cal flash, yes it will happen that quick. Takes me about a minute to cal flash a DSP5 into a BOSCH controller.
    1995 GMC 2500 SUBURBAN powered by 01 DURAMAX/ALLISON, little of this, a little of that,
    DIAMONDEYE 4" exhaust, CORSA muffler, AFE stage 1 dry filter, custom tuning by me, KENNEDY single pump and pump rub kit.

  3. #3
    Lifetime Member
    Join Date
    Apr 2008
    Posts
    269

    Default

    I will ask the same as I did on the Diesel Place forum. Are you the original owner of the vehicle? If not maybe it is tuned. Have you gone to a dealer to see if they can flash a stock tune in it? If they can't then I would say either some bad or not fully connected wiring or a bad ECM.

    Brian
    2007.5 GMT-900 Chevrolet Silverado 2500HD CC/LB LTZ 4x4 Summit White.
    With the LMM Duramax 365hp/660tq, MW7 Allison 1000 6-speed
    EFILive LMM DSP5 Settings, 500HP, 450HP, 400HP,Tow with Turbine Brake, and Stock HP.

    UA Steamfitter, Local 136 Evansville, IN - Remember if you want to play you got to pay.

  4. #4
    Lifetime Member Mitco39's Avatar
    Join Date
    Jan 2009
    Posts
    648

    Default

    Run the program as admin, if you dont it will do this. I have all my efi live programs set to run as admin all the time. To run it as administrator just right click the program you want to open then select run as administrator.

  5. #5
    Junior Member derrickmanx1's Avatar
    Join Date
    Mar 2011
    Posts
    13

    Default

    Cig lighter is good. I'm the original tuner because I loaded this tuning into the truck. I can tune the tcm but it will not read the tune or change the tire size of this tune. I've tryed full flashing cal flashing. It doesn't even bring the progress bar up.

  6. #6
    Junior Member derrickmanx1's Avatar
    Join Date
    Mar 2011
    Posts
    13

    Default

    I'll definately try the administrator thing when I get a chance to mess with it. It's still running it just won't change.

  7. #7
    Lifetime Member
    Join Date
    Mar 2006
    Posts
    4,935

    Default

    You need to update at least your V2's firmware, latest is 2.07.28. Start with that, then try it again (set the programs to run as Administrator too). Also, if that doesnt work then try using V8 to flash the ECM as well.
    Last edited by ScarabEpic22; May 7th, 2012 at 02:11 AM.
    ~Erik~
    2013 Sonic RS Manual - 1.4L I4T E78, tuned, turbo mods, etc.
    2008 TrailBlazer SS 3SS AWD Summit White - LS2 E67/T42, bolt ons, suspension, etc.
    2002 Chevy TrailBlazer LT 4X4 Summit White - 4.2L I6 P10, lifted, wheels, etc.

  8. #8
    Junior Member derrickmanx1's Avatar
    Join Date
    Mar 2011
    Posts
    13

    Default

    I had updated the day before trying this flash. I'll still update it again

  9. #9
    Lifetime Member IdahoRob's Avatar
    Join Date
    Apr 2006
    Posts
    736

    Default

    This is your problem. Run as Admin.
    2013 LML, 550hp with factory emissions, stock cp4 and compound turbos.
    2002 LBZ, 4x4 (Max'd Out) 6000lbs 9.36 @ 154 mph NHRDA Champion and Record holder
    1965 El Camino, duramax 9.6 @ 149MPH

    All EFI tuned by Adrenaline Truck Performance

  10. #10
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    This Admin permissions issue should all be fixed in the next update.
    I no longer monitor the forum, please either post your question or create a support ticket.

Similar Threads

  1. ECM Pins for DSP, trouble with wire...
    By andrewjamesbond1 in forum General (Diesel)
    Replies: 9
    Last Post: February 16th, 2012, 11:18 AM
  2. Issues with locking ECM then flashing again
    By LBZoom in forum General (Diesel)
    Replies: 5
    Last Post: October 26th, 2011, 03:42 AM
  3. Trouble flashing in a tune
    By Chris81 in forum FlashScan V2
    Replies: 2
    Last Post: January 4th, 2011, 09:03 AM
  4. Flashing ECM Alone?
    By Nemo in forum General (Diesel)
    Replies: 4
    Last Post: April 12th, 2010, 08:18 AM
  5. Trouble Communicating with E38 ECM
    By philip.long in forum E37, E38 & E67 PFI ECM's
    Replies: 5
    Last Post: January 25th, 2009, 08:33 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •