Results 1 to 7 of 7

Thread: E40 PCM shift light output? And fan

  1. #1

    Default E40 PCM shift light output? And fan

    Hope it's the correct section.

    LS2 with E40 PCM (it's in a Mazda rx7) looking thro the options it has a shift light does anyone know what pin this in or does it output thro the BCM (which we don't have) ??

    Is there a patch to gain proper control of normal/aux fans?

    Thanks

    Blair

  2. #2
    Senior Member Chuck L.'s Avatar
    Join Date
    Feb 2006
    Posts
    184

    Default

    Next door down!.. Gen4
    Chuck L.
    CODY Motorsports
    Fuel Injector Service
    Madison, GA.
    706-342-3152
    770-265-5144 [C]

  3. #3
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    It's not an LS1/LS6, so I moved it...

  4. #4
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    It's a matter of locating a 2005/6 GTO/HSV engine controls wiring diagram...

  5. #5

    Default

    Thanks Joe I have the wiring diag but can't see it so unless anybody else has any idea's we'll be using an rpm switch to turn the air on off.

    What about fan control any inspiration?

  6. #6
    Lifetime Member
    Join Date
    Aug 2010
    Posts
    1,934

    Default

    Quote Originally Posted by bikealarmblair View Post
    ... LS2 with E40 PCM ... looking thro the options it has a shift light does anyone know what pin this in or does it output thro the BCM (which we don't have) ?? ...
    Shift light (if the ECM is so programmed) is via Serial Data to the IPC.


    ... Is there a patch to gain proper control of normal/aux fans? ...
    There is no operational patch to control the E-Fans via ECT below 192 F. The E-Fans are controlled with respect to ECT, via % PWM in G0901. And similarly in G0902 with respect to A/C pressure.

    Low Fan - C1 (Blue) pin 36.
    High Fan - C1 (Blue) pin 56.


    Regards,
    Taz

  7. #7
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Ah, shift light is done over the serial bus, that explains why the engine controls wiring diagram shows no control.

Similar Threads

  1. Replies: 8
    Last Post: December 19th, 2011, 02:29 AM
  2. Can the 1-4 shift light be controlled on the e38s like the 0411 PCM?
    By Highlander in forum E37, E38 & E67 PFI ECM's
    Replies: 4
    Last Post: March 10th, 2011, 12:33 PM
  3. Using the pcm controlled shift light
    By Chris81 in forum General (Petrol, Gas, Ethanol)
    Replies: 4
    Last Post: December 4th, 2008, 04:56 AM
  4. Can I setup output for elec fan
    By Madspeed in forum Duramax LLY
    Replies: 4
    Last Post: June 15th, 2008, 05:50 AM
  5. VT Mil Light & Fan
    By saeb in forum EFILive V4
    Replies: 0
    Last Post: March 11th, 2006, 08:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •