Page 3 of 6 FirstFirst 12345 ... LastLast
Results 21 to 30 of 57

Thread: Help with CalcVE Tuning Filter

  1. #21
    Senior Member jeff keyuk's Avatar
    Join Date
    Jun 2008
    Posts
    127

    Default

    Hey joe ! Can't remember how to sent the log file.

  2. #22
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Hey Jeff,

    Attach the log file (filename ends in .efi) file like this:


    start your reply, and then do this:

    . . .
    5. below the reply box click Go Advanced, scroll down a little, click Manage Attachments (see 1 in pic below);
    6. in Manage Attachment popup box click Add Files (see 2 in pic);
    7. in Upload Files popup box click Select Files (see 3) and locate file, select it, click OK, file appears in Upload Files popup box;
    8. click Upload Files (see 4), file appears in Attachments section of Manage Attachments popup box;
    9. click Done (see 5), file appears in Attachments section of the post;
    A. finishing typing your reply, and submit the reply.


    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	manageattachments.png 
Views:	191 
Size:	505.6 KB 
ID:	14081  

  3. #23
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    On the PIDs tab, highlight MAP and MAF and go rightclick->Metric.

  4. #24
    Senior Member jeff keyuk's Avatar
    Join Date
    Jun 2008
    Posts
    127

    Default

    Hi joe ! Thanks again!
    Attached Files Attached Files

  5. #25
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Is your MAF failed...?

    ( I see DTC p0103, this means the PCM is using only the VE )



    Wideband voltage is very wobbly...

  6. #26
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Also, LTFT's don't match side-to-side...

  7. #27
    Senior Member jeff keyuk's Avatar
    Join Date
    Jun 2008
    Posts
    127

    Default

    Hey Joe! P0103 was set at NO MIL , I set it back at ( MIL ) Sorry ! I Did not set it back for close loop tuning! I when't back over all the table I change for the open loop tuning. I will try it again to make a log run ,and I will sent it back to you! Thanks Joe. Slow leaner!
    Last edited by jeff keyuk; October 26th, 2012 at 08:59 AM. Reason: adjust text!

  8. #28
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Jeff,

    No worries.

    Are you doing Calc.VET or AutoVE...?

  9. #29
    Senior Member jeff keyuk's Avatar
    Join Date
    Jun 2008
    Posts
    127

    Default

    Hi Joe
    I am doing Calc.VE tuning !

  10. #30
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Ok, then enable the MAF (set C2901-3 back to stock)...

    enable MAF DTC/MIL reporting (set C6002 P0101-3 to MIL, set C6001 P0101-3 to A:1-Trip)...

    verify that none of the MAF DTC's appear during any drive.

Page 3 of 6 FirstFirst 12345 ... LastLast

Similar Threads

  1. Auto VE Tuning Data Filter Question
    By jeff keyuk in forum Tutorials
    Replies: 24
    Last Post: August 17th, 2012, 11:27 AM
  2. filter setting
    By myws6formula in forum RoadRunner Real-Time PCM Emulator
    Replies: 35
    Last Post: April 22nd, 2012, 03:24 PM
  3. Closed Loop Filter- Tuning w/o WBo2
    By Crunkmaro in forum Gen III V8 Specific
    Replies: 4
    Last Post: August 6th, 2011, 12:02 PM
  4. Help with AutoVe and CalcVE tired last night.
    By pavetim in forum Gen III V8 Specific
    Replies: 8
    Last Post: December 18th, 2010, 11:49 AM
  5. CalcVE insanity check... duh?
    By Wolfie in forum Gen III V8 Specific
    Replies: 19
    Last Post: May 21st, 2010, 08:59 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •