Results 1 to 4 of 4

Thread: LS7 inj??

  1. #1
    Senior Member Chuck L.'s Avatar
    Join Date
    Feb 2006
    Posts
    184

    Question LS7 inj??

    Vehicle is an 07 Escalade.
    Am looking at installing the LS7 injs, sold by FAST. [No info available, that I can find on their site. Calling proved to be a waste of time.] The injs are advertised as 39PPH. Shows as pt # 30397. I tracked the part number via a comparo elsewhere, and find that the LS7 inj is listed there also, as 39#. There are additional #'s listed as:
    Bosch 0280158051
    GM 12576341
    The tune that I am looking at in Tune Depot,[06/07 LS7 Vette/E38], shows that inj as being 41.737#. The min pulse shows as .7969, volt mod 1.00.

    The ? Which rate is correct?

    TIA!
    Chuck L.
    CODY Motorsports
    Fuel Injector Service
    Madison, GA.
    706-342-3152
    770-265-5144 [C]

  2. #2
    Member
    Join Date
    Dec 2006
    Posts
    96

    Default

    Since the LS7 requires premium fuel, they might use the 41.7 number for flow vs that of inert gas. The 8.1 Marine injectors were often used on the trucks because of the direct fits and flowed 43.82/4 bar, when calculated for regular gas they were 45.13 ppm at 4 bar.
    Last edited by Gordy M; February 26th, 2013 at 03:06 AM.

  3. #3
    Senior Member Chuck L.'s Avatar
    Join Date
    Feb 2006
    Posts
    184

    Default

    Gordy, thanks for the response! I know the car will run premium only. I'll use the stock Tune Depot values.
    Chuck L.
    CODY Motorsports
    Fuel Injector Service
    Madison, GA.
    706-342-3152
    770-265-5144 [C]

  4. #4
    Senior Member J.Abbott's Avatar
    Join Date
    Aug 2010
    Posts
    113

    Default

    They are 42lb injectors. Depends on what the flow was but Bosch flows at 3 bar and GM flows at 4 bar on that injector. If you do the math it is 37 lbs per hour so they must have been showing that.

Similar Threads

  1. Inj info....
    By Chuck L. in forum Gen III V8 Specific
    Replies: 13
    Last Post: July 26th, 2012, 02:11 PM
  2. LBZ-Pilot Inj 2
    By killerbee in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 4
    Last Post: July 27th, 2009, 07:03 PM
  3. pilot inj 1 quantity-b9101 or b9102
    By killerbee in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 3
    Last Post: May 4th, 2009, 02:33 PM
  4. Fuel Inj load test?
    By Beer99C5 in forum Gen III V8 Specific
    Replies: 0
    Last Post: June 27th, 2008, 10:01 PM
  5. Inj duty cycle too high?
    By Bruce Melton in forum General (Petrol, Gas, Ethanol)
    Replies: 6
    Last Post: April 8th, 2006, 09:08 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •