"BLACK"-2007 Yukon Denali 6.2 gasser EFI AutoCal
"BLACK"-2007.5 GMC Sierra 3500HD SRW, LMM Dmax, EFI AutoCal/Spade
joecar,
I took out the T43, now only 38 is selected with 12 pid's, it still will NOT show any pid's to view.
I scrolled down to "Select Pid's" (ok) then 38 shows (ok) then it goes directly to "Record Data" when I hit (ok) it starts scanner time counting.
The AutoCal will save the recorded data but that is all it will do besides the tuning.
I know the AutoCal is a little limited on space could my tunes installed be affecting PID viewing ?
I have 4 tunes installed, 38 mod coz file, 38 stock coz file, T43 mod ctz file, T43 stock coz file, my tuner has not done a coz file on the T43 mod.
I'm not comfortable with only having the stock files on the computer and putting only the mod files on the AutoCal, I'm concerned about possible computer issues and loosing them.
?, I have a AutoCal setting around that I am not using anymore, if I took the tune files off of the AutoCal I'm not using anymore could it be used as a scanner on other vehicles ?
That is if my problem with viewing PID's is because of the tuning space I'm using on the AutoCals that I am using now.
I do thank you for taking the time to try to help me solve this.
Also, I'm including another RedNeck snapshot of what's in my AutoCal, I tried the proper way but could not figure it out.
Heres the bootblock and Firmware #'s
Last edited by RVDAN; March 25th, 2013 at 06:22 AM.
"BLACK"-2007 Yukon Denali 6.2 gasser EFI AutoCal
"BLACK"-2007.5 GMC Sierra 3500HD SRW, LMM Dmax, EFI AutoCal/Spade
joecar,
I just re-configured my spare AutoCal (that I'm not using) to read only engine 38 and only one pid MAF g/s and it does not show pid's either on my gasser ?
"BLACK"-2007 Yukon Denali 6.2 gasser EFI AutoCal
"BLACK"-2007.5 GMC Sierra 3500HD SRW, LMM Dmax, EFI AutoCal/Spade
Can you post the Options.txt saved from the BBx window.
BBX saved files saved ctrl s.txtI'm not sure if this is what your looking for, I had the AutoCal plugged in and went from there.
If I'm reading it right it looks like nothing is Y for the PID's even though they show on the selected pid screen and I did programmed them in.
E38 is the only engine that shows active Y and that's what I selected.
Last edited by RVDAN; March 25th, 2013 at 10:50 AM.
"BLACK"-2007 Yukon Denali 6.2 gasser EFI AutoCal
"BLACK"-2007.5 GMC Sierra 3500HD SRW, LMM Dmax, EFI AutoCal/Spade
I tested your file here and it appears to work ok. I removed the AFRATIO_M PID since it was not supported on my test E38 controller.
When the AutoCal is showing the time counting, press the "Next" button to sroll down thru each PID, press the "Prev" button to scroll back up, eventually getting to "Exit" at which stage pressing OK will stop the data log.
Regards
Paul
Before asking for help, please read this.
I was never told to view the select PID worked the way you explained, thank you.
So when I scroll down after the time is counting on the data log I will see the PID's and be able to read whats going on.
Like MAF g/s at idle or while driving or any of the other PID's on the list?
I check this out tomorrow morning, I do hope this works I'm worn out trying to figure out what the issue was.
THANK YOU
"BLACK"-2007 Yukon Denali 6.2 gasser EFI AutoCal
"BLACK"-2007.5 GMC Sierra 3500HD SRW, LMM Dmax, EFI AutoCal/Spade