Page 2 of 6 FirstFirst 1234 ... LastLast
Results 11 to 20 of 57

Thread: Just finished my COS tune and no start

  1. #11
    Member
    Join Date
    Jan 2012
    Posts
    70

    Default

    That's what it says to set them at in the tutorial. What would you suggest setting them to and why?

    Thanks

  2. #12
    Lifetime Member limited cv8r's Avatar
    Join Date
    May 2005
    Posts
    567

    Default

    Try attached tune,out of range fixed.
    Your settings weren't wrong,sometimes with out of range stuff you just need to change it to something lower than max limit and save tune,you can then usually open saved tune reset back to max limit if wanted,save tune again,reopen tune and hopefully nothing is out of range anymore.
    Attached Files Attached Files
    It's all good until it goes "Bang"

  3. #13
    Member
    Join Date
    Jan 2012
    Posts
    70

    Default

    Makes sense Thanks for the help!! still learning all the ins and outs lol.

  4. #14
    Lifetime Member limited cv8r's Avatar
    Join Date
    May 2005
    Posts
    567

    Default

    Also your VIN is all zero's and B3647 & B3649 are set to lean out in the 95/100 columns. Looks like a bit of confusion between using lambda & EQ ratio.
    It's all good until it goes "Bang"

  5. #15
    Member
    Join Date
    Jan 2012
    Posts
    70

    Default

    I already fixed the VIN ill look at B3647 and B3649

  6. #16
    Member
    Join Date
    Jan 2012
    Posts
    70

    Default

    Yes you are right that is wrong. now I am forgetting how to change the units from lambo to eq.

  7. #17
    Member
    Join Date
    Jan 2012
    Posts
    70

    Default

    or do I need to adjust the numbers to be lambo instead of EQ ratio

  8. #18
    Lifetime Member limited cv8r's Avatar
    Join Date
    May 2005
    Posts
    567

    Default

    edit,properties,commanded fuel values.
    Just remember you will need to close and reopen your tune before the change will take effect.
    It's all good until it goes "Bang"

  9. #19
    Lifetime Member limited cv8r's Avatar
    Join Date
    May 2005
    Posts
    567

    Default

    Do as suggested above , then adjust as needed to suit what your using.
    It's all good until it goes "Bang"

  10. #20
    Member
    Join Date
    Jan 2012
    Posts
    70

    Default

    Ok this is what I have now. This rookies feet are getting wet lol. Riebel cos3 0001.tun

    Thanks so much for the help!

Page 2 of 6 FirstFirst 1234 ... LastLast

Similar Threads

  1. Need a COS to start with
    By pullincrazy88 in forum Custom Operating Systems
    Replies: 0
    Last Post: June 12th, 2011, 09:39 AM
  2. COS and no start
    By turbogtu in forum General
    Replies: 1
    Last Post: September 15th, 2009, 01:27 PM
  3. car wont start with COS#5
    By articSS in forum Custom Operating Systems
    Replies: 3
    Last Post: September 19th, 2007, 11:43 AM
  4. Almost finished AutoVE
    By Spdfrk1990 in forum Gen III V8 Specific
    Replies: 26
    Last Post: July 6th, 2007, 01:27 PM
  5. Finished 3 bar SD TUNE. How do I return to closed loop?
    By nitrorocket in forum General (Petrol, Gas, Ethanol)
    Replies: 26
    Last Post: October 13th, 2005, 03:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •