Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 40

Thread: Analog wideband help for new starters

  1. #21
    Junior Member
    Join Date
    Nov 2013
    Posts
    35

    Default

    Nar mate i just had it hooked up to the v2 alone and thought it may give me a read out, can you see the voltages in the data screen with the car running? On the wo2 screen it still dosnt recognise the wideband.

  2. #22
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default

    you won't see wbo2 data on the v2 screen unless it connected via serial.

    analog voltages should be displayed with passthru.
    512k RoadRunner Firmware 12.14R
    FlashScan V2 Bootblock V2.07.04 Firmware V2.07.22 EFILive V7.5.7 (Build 191) V8.2.1 (Build 181)
    LC-1 WBO2

    _________________________________________________

  3. #23
    Junior Member
    Join Date
    Nov 2013
    Posts
    35

    Default

    Ok my current wideband ( haltech dual ) isn't serial capable, do i select external wideband pid in v7 passthru and will it work see i don't really know all i seem to be getting here is what I'm doing wrong. I was hopping this thread would help me and others so far it is confusing.

  4. #24
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default

    what model do you have?

    HWC, HDWC, HT059970 / HT059980
    512k RoadRunner Firmware 12.14R
    FlashScan V2 Bootblock V2.07.04 Firmware V2.07.22 EFILive V7.5.7 (Build 191) V8.2.1 (Build 181)
    LC-1 WBO2

    _________________________________________________

  5. #25
    Junior Member
    Join Date
    Nov 2013
    Posts
    35

    Default

    Its the old style dual HDWC ( I'm only using it as a single ) not the new one with the CAN capabilities to integrate with a haltech computer.

  6. #26
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default

    not the lc-1 clone.

    signal wire #1 (white) connected to AD1+
    signal wire #2 (grey) connected to AD2+
    512k RoadRunner Firmware 12.14R
    FlashScan V2 Bootblock V2.07.04 Firmware V2.07.22 EFILive V7.5.7 (Build 191) V8.2.1 (Build 181)
    LC-1 WBO2

    _________________________________________________

  7. #27
    Junior Member
    Join Date
    Nov 2013
    Posts
    35

    Default

    Not sure what you mean by not the lc-1 clone the signal wires for the haltech are white and blue.
    Last edited by braapp; December 29th, 2013 at 09:13 PM.

  8. #28
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    What about the ground wire...?

  9. #29
    Lifetime Member darcy's Avatar
    Join Date
    Feb 2012
    Posts
    223

    Default

    With the wideband wired up to the V2's external input AD1, log the pid EXT.AD1 - this will give you the widebands output voltage.
    Then you need to log a calculated pid that will convert the voltage to an AFR that you can relate to. Log CALC.PLX1 (PLX uses the 2v+10 equation that I believe Haltech also uses for converting voltage to AFR) - now you will have AFR in your log too.
    From there you can use the CALC.BEN_PLX1 for your correction factor.

    The above values assume stoich is 14.7 - which is ok for pure gasoline - working in EQR/lamba is better but requires some changes to the calc pids that can wait until you're up and running.

  10. #30
    Junior Member
    Join Date
    Nov 2013
    Posts
    35

    Default

    Quote Originally Posted by darcy View Post
    With the wideband wired up to the V2's external input AD1, log the pid EXT.AD1 - this will give you the widebands output voltage.
    Then you need to log a calculated pid that will convert the voltage to an AFR that you can relate to. Log CALC.PLX1 (PLX uses the 2v+10 equation that I believe Haltech also uses for converting voltage to AFR) - now you will have AFR in your log too.
    From there you can use the CALC.BEN_PLX1 for your correction factor.

    The above values assume stoich is 14.7 - which is ok for pure gasoline - working in EQR/lamba is better but requires some changes to the calc pids that can wait until you're up and running.
    Thanks Darcy this has sort of been what I've been after all along cheers. Can these pids be found in the v7 list.

Page 3 of 4 FirstFirst 1234 LastLast

Similar Threads

  1. Error $5 (analog wideband logging)
    By rumblebox in forum FlashScan V2
    Replies: 25
    Last Post: August 22nd, 2013, 04:07 AM
  2. Analog wideband install?????
    By T&A Custom Rides in forum General
    Replies: 5
    Last Post: January 30th, 2012, 07:52 PM
  3. Replies: 9
    Last Post: November 16th, 2011, 02:17 AM
  4. Autronic MAFM1 wideband analog to V2
    By APS Luis in forum External A/D inputs
    Replies: 4
    Last Post: July 10th, 2011, 01:30 PM
  5. Lost all wideband analog and serial pids
    By Wichita Dyno in forum General
    Replies: 13
    Last Post: August 23rd, 2010, 03:24 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •