Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: NTK AFX Wiring and PID Advice Needed

  1. #1
    Junior Member
    Join Date
    Feb 2013
    Posts
    34

    Default NTK AFX Wiring and PID Advice Needed

    I know these subjects have been brought up a few times, but I’m getting information from all over the place, and it would be great if I could get up-to-date and accurate info from someone who has experience working with V2 and the NTK AFX wideband.

    The AFX instruction manual says the brown wire MUST be connected to the same ground location as the two black wires, as close to the battery ground as possible for the most accurate and precise readings. I’ve extended the brown wire so that it can reach, as the manual says is okay to do. All I’m left with now is a yellow wire for A1 input?

    (I've read elsewhere that the brown wire goes to the A1 ground location on the scanner. If so, what makes that safe to do when the manual states it should be grounded to the same spot as the black wires? Would it work either way?)

    After everything’s hooked up and ready to go, if I want to use BBL, I set scanner to: automatically select ALL external analog PIDs? Which PIDs do I use in ScanTool?

    I have the most recent versions of 7.5 and 8. What do I need to do to record my AFX readings in Lambda, or is that PID already in my software now?

  2. #2
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    If brown wire is signal ground, then yes it goes to FSV2 AD1- input.

    Can you post the AFX user manual pdf...

  3. #3

  4. #4
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Using V8 S&T software, goto Devices, goto Logging, checkmark "Automatically select all external analog pids", click Save (save to file "Settings.dat", click Program (to V2), and then exit.

  5. #5
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Yes, connect as follows:
    - yellow directly to FSV2 AD1+ input,
    - brown directly to FSV2 AD1- input.

    To avoid ground loops, avoid connecting brown to chassis ground (or other grounds).

  6. #6
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    i.e. connect the brown wire (signal ground) directly to FSV2's AD1- input, and to nothing else.

  7. #7
    Junior Member
    Join Date
    Feb 2013
    Posts
    34

    Default

    Okay, I hope to get it up and running tomorrow. I’ll have to remove the extension I added to that wire.

    As far as logging PIDs goes, will CALC.AFR_NGK1 log what the AFX shows on its display? That’s pretty much all I want right now, except that I’d also like to have that logged as an EQ Ratio or Lambda instead.

  8. #8
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by 12_Square View Post
    ...

    As far as logging PIDs goes, will CALC.AFR_NGK1 log what the AFX shows on its display? That’s pretty much all I want right now, except that I’d also like to have that logged as an EQ Ratio or Lambda instead.
    Yes, CALC.AFR_NGK1.

    See attached calc_pids.txt for eqr/lambda based WO2BEN pid.
    Attached Files Attached Files
    Last edited by joecar; February 5th, 2014 at 10:25 AM.

  9. #9
    Junior Member
    Join Date
    Feb 2013
    Posts
    34

    Default

    What would this do?

    {EXT.AD1}*0.096+0.62

    I'm hoping for a Lamda number from my wideband, in relation to nothing else.

  10. #10
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default

    {EXT.AD1}*0.096+0.62 = Lamda
    512k RoadRunner Firmware 12.14R
    FlashScan V2 Bootblock V2.07.04 Firmware V2.07.22 EFILive V7.5.7 (Build 191) V8.2.1 (Build 181)
    LC-1 WBO2

    _________________________________________________

Page 1 of 2 12 LastLast

Similar Threads

  1. Advice needed, please take a look to my tune
    By DocZ28 in forum Gen III V8 Specific
    Replies: 34
    Last Post: October 17th, 2012, 12:12 PM
  2. 4 wire Universal NTK Narrow Band O2 sensor wiring?????'s
    By GAMEOVER in forum General (Petrol, Gas, Ethanol)
    Replies: 3
    Last Post: January 19th, 2011, 09:40 AM
  3. Wiring NGK Powerdex AFX to the V1 scan tool
    By voda1 in forum FlashScan V1
    Replies: 1
    Last Post: June 24th, 2010, 05:41 AM
  4. LS2 with GMPP E67 - advice needed
    By V8RX7 in forum E37, E38 & E67 PFI ECM's
    Replies: 4
    Last Post: July 2nd, 2009, 11:20 PM
  5. Advice needed
    By JuhaniLS1 in forum Gen III V8 Specific
    Replies: 5
    Last Post: February 15th, 2007, 12:26 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •