Results 1 to 6 of 6

Thread: Check sum error

  1. #1
    Lifetime Member
    Join Date
    Apr 2008
    Posts
    469

    Default Check sum error

    Hi,

    I have Camaro 2013 that was previously with the Diablo Sport. I read the file as usual but when i try to flash the file back it gives "check sum error"

    I tried to flash back diablo file but again " check sum error", i tried full flash and no luck.

    Thanks,
    Regards,

    Odd Boy

  2. #2
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Common problem with Diablo tunes, can you post the file up here so it can be fixed?
    I no longer monitor the forum, please either post your question or create a support ticket.

  3. #3
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Hi Ross,

    This is the E38 file I keep getting "checksum error" at the end of flashing, when flashing using V8 or BBF (see attached)...

    my customer says he flashed this into his ECM using GM TIS.



    I don't see any error when flashing this file using V7


    ( sorry, I can't find the other thread where you said to attach such files )
    Attached Files Attached Files

  4. #4
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Joe, I think this is a different issue to the Diablo CVN fudging causing the checksum error.

    Edit: This is the same issue as odd_boy, I suspect your file Joe is from LS2Edit, I am 99% sure this is not a TIS flashed tune. However that doesn't explain why the ECM flashes with V7.5 but not V8, both should fail.
    I no longer monitor the forum, please either post your question or create a support ticket.

  5. #5
    Lifetime Member
    Join Date
    Apr 2008
    Posts
    469
    Regards,

    Odd Boy

  6. #6
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by GMPX View Post
    Joe, I think this is a different issue to the Diablo CVN fudging causing the checksum error.

    Edit: This is the same issue as odd_boy, I suspect your file Joe is from LS2Edit, I am 99% sure this is not a TIS flashed tune. However that doesn't explain why the ECM flashes with V7.5 but not V8, both should fail.
    Yes, V7 flashes just fine (and engine starts fine).


    I'll query my customer further regarding TIS vs LS2Edit.

Similar Threads

  1. lbz check sum error
    By relentless addiction in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 1
    Last Post: October 27th, 2011, 12:40 PM
  2. Check Sum
    By TBMSport in forum 6 speed/8 speed RWD/FWD Transmission Tuning (incl T43, T76, T87)
    Replies: 1
    Last Post: September 6th, 2010, 10:32 AM
  3. check out my VE
    By nchristian in forum Gen III V8 Specific
    Replies: 0
    Last Post: June 17th, 2009, 03:01 PM
  4. Range Check Error
    By jsttry in forum General (Petrol, Gas, Ethanol)
    Replies: 1
    Last Post: October 31st, 2006, 10:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •