Does this build have the beta version of the "anti tune" fix for the CMC? if so I have a customer that could benefit from that today, otherwise I'll have to ship him a smarty for now. Thanks
Does this build have the beta version of the "anti tune" fix for the CMC? if so I have a customer that could benefit from that today, otherwise I'll have to ship him a smarty for now. Thanks
Peace Through Torque
Punisher Performance DSP5 Tuning, PPE Dual CP3's, 68mm Fleece Cheetah, Punisher Built trans w/ Suncoast Parts, Airdog 165, SoCal 100% Overs, ARP Studs
2013 NHRDA Sportsman World Champion
www.PunisherPerformance.com
Speedometer segments in E38 trucks seem to have different values in them. When looking at the history of a tune I already done the values dont match whats shown. Both tunes in imperial speedometer settings.
I no longer monitor the forum, please either post your question or create a support ticket.
I no longer monitor the forum, please either post your question or create a support ticket.
A known issue with the V7.5 tune tool editor software has been confirmed. If you attempt to open a tune file that uses a *.cax (user defined calibration definition) then the editor will not load the EFILive defined or user defined calibrations correctly. Current workaround is to rename the *.cax file so that it does not get loaded. We are working on a fix and hope to issue an update in the next 24 hours.
Regards
Paul
Before asking for help, please read this.
We are trying to figure out an issue with a $0502 code on an autocal using this update. We are trying to flash a E86B controller. And I tried resetting it up several times, but we keep getting the same error.
The only thing that I can think of is maybe it is missing a file in the install for it? Here is the file list that we currently have loaded on the autocal.
The only thing that stands out is that it is missing a E86B_F.obj?
I tried looking for the file in "C:\Program Files (x86)\EfiLive\V8\Config" but no E86B_F.obj. I resaved the file using the new updated v8 software. No avail.
I only included the E86A ecm because i thought maybe it would help. but no... Tried clearing config system and reprogramming the config files using V8, under BBX, F3: Tune, selecting the E86B controller and choosing "Program selections and configuration files (slower)" Nope.... Get the same list as above and the $0502.
Ill include a copy of the options.txt
Options.txt
Josh
'04 GMC LLY - L5P, Motech, 6-Spd Conv. ML Trans.
'05 GMC LLY - 250%, 12mm, 67mm Custom Turbo, 6-Spd Conv. ML Trans
'19 3500 RAM - Tuned Aisin 0_o
Got to the V8 Scan Tune program, BBX - F5 then the "Tune" tab use the green "+" and add the E86B controller by right clicking add controller
Josh
'04 GMC LLY - L5P, Motech, 6-Spd Conv. ML Trans.
'05 GMC LLY - 250%, 12mm, 67mm Custom Turbo, 6-Spd Conv. ML Trans
'19 3500 RAM - Tuned Aisin 0_o
Format the File System then reprogram it
Formatted Data & Config systems using EFILive explorer. Copied over all the tunes 1 CTZ file for the full flash and 4 COZ. All were re-saved using 8.2.2.260. Choosing the " Save, For AutoCal" option under the Save Button.
Then created a fresh options.txt. Set it up like so.
These are the files that were copied over.
Still $0502.....
BootBlock is 2.07.07 Feb 07, 2014
Firmware is 2.07.66 Sep 12, 2014
Josh
'04 GMC LLY - L5P, Motech, 6-Spd Conv. ML Trans.
'05 GMC LLY - 250%, 12mm, 67mm Custom Turbo, 6-Spd Conv. ML Trans
'19 3500 RAM - Tuned Aisin 0_o