Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Dynamic vehicle testing

  1. #1
    Lifetime Member
    Join Date
    Dec 2005
    Posts
    266

    Default Dynamic vehicle testing

    Any chance of adding forced regen Table/Tab for the LML under DVT(F12) like the LMM has?

    Using the LMM DVT will not work on the LML controller. I could not get it to work.

    It's nice to tune these controllers with the emission in tacked. Its a pain when there's a regen hickup and the vehicel refuses to start the regen cycle.

    I was in the sad predicament of having to locating a dealer today to do just that. Get the vehicle serviced for "Forced Regen" and they had no idea why it would not start the process.
    2011 LML 3500HD CC D/A 4x4
    2006 LBZ 3500 CC D/A 4x4 Sold
    2001 LB7 2500HD D/A 4x4 Sold

  2. #2
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    You mean Bosch didn't keep the same process between ECM's
    I'm not sure when we might be able to look in to this, does the TechII support the LML or is it MDI only?
    I no longer monitor the forum, please either post your question or create a support ticket.

  3. #3
    Lifetime Member Mitco39's Avatar
    Join Date
    Jan 2009
    Posts
    648

    Default

    I believe the techII works up to 2013, in 14 they switched it around and we all know about the 15s

  4. #4
    Member mpdtune's Avatar
    Join Date
    Jul 2013
    Posts
    89

    Default

    Quote Originally Posted by GMPX View Post
    You mean Bosch didn't keep the same process between ECM's
    I'm not sure when we might be able to look in to this, does the TechII support the LML or is it MDI only?
    Tech2Win will do.

  5. #5
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    We don't have a subscription for Tech2Win, just TIS2WEB and Service. Not putting it in the too hard basket, just some higher priority stuff to get done first I'm afraid. Thing is, when the original post said it didn't work was there any indication that the ECM responded with an error or just that nothing happened?
    I no longer monitor the forum, please either post your question or create a support ticket.

  6. #6
    Lifetime Member
    Join Date
    Dec 2005
    Posts
    266

    Default

    Ross,

    I recall a message with a red line DVT: Engine speed not zero after selecting Service Regen and Turn On
    2011 LML 3500HD CC D/A 4x4
    2006 LBZ 3500 CC D/A 4x4 Sold
    2001 LB7 2500HD D/A 4x4 Sold

  7. #7
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    You'd think the engine might need to be running

    FYI for LML......

    The following conditions must be met in order to enable DPF Service Regeneration:

    • DTCs P2463 is the only active DTC.
    • The battery voltage is greater than 10 V.
    • The engine speed is between 500–2,700 RPM.
    • The vehicle speed is 0.
    • The transmission is not in Drive or Reverse
    • The exhaust gas temperature (EGT) sensors 1 is between 20–500°C (68–932°F).
    • The exhaust gas temperature (EGT) sensors 3 is between 20–735°C (68–1,355°F).
    • The engine coolant temperature (ECT) sensor is greater than 70°C (158°F).
    • The fuel temperature is less than 150°C (302°F).
    • The BARO pressure is greater than 40 kPa (5.8 psi)
    • The APP sensor is less than 1 percent.
    • The diesel exhaust fluid temperature is greater than −7°C ( +19°F).
    • The diesel exhaust fluid tank is not empty.
    • The brake pedal and accelerator pedal are in the released position.
    • The song 'Ca Plane Pour Moi' by Plastic Bertrand must be on repeat on your MyLink radio
    • The transmission is in Park or Neutral.

    The DPF Service Regeneration will be terminated if any of the following conditions occur:

    • The DPF Service Regeneration is commanded Off using the scan tool.
    • The scan tool is disconnected from the vehicle.
    • The vehicle is shifted out or Park or Neutral.
    • The brake or accelerator pedal is applied.
    Last edited by GMPX; April 28th, 2015 at 01:30 PM.
    I no longer monitor the forum, please either post your question or create a support ticket.

  8. #8
    Member mpdtune's Avatar
    Join Date
    Jul 2013
    Posts
    89

    Default

    Quote Originally Posted by GMPX View Post
    We don't have a subscription for Tech2Win, just TIS2WEB and Service. Not putting it in the too hard basket, just some higher priority stuff to get done first I'm afraid. Thing is, when the original post said it didn't work was there any indication that the ECM responded with an error or just that nothing happened?
    Tech2Win without a truck to connect to would be tricky to work with. Any chance of getting the true Fast Learn Program for the TCMs in the Scan Tool?

  9. #9
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    I think we looked at this years ago and it was a fairly complex procedure that needed to be followed, something the DVT core of the software was not capable of.
    I no longer monitor the forum, please either post your question or create a support ticket.

  10. #10
    Lifetime Member
    Join Date
    Nov 2005
    Posts
    1,753

    Default

    Quote Originally Posted by GMPX View Post
    You'd think the engine might need to be running

    FYI for LML......

    The following conditions must be met in order to enable DPF Service Regeneration:

    • DTCs P2463 is the only active DTC.
    • The battery voltage is greater than 10 V.
    • The engine speed is between 500–2,700 RPM.
    • The vehicle speed is 0.
    • The transmission is not in Drive or Reverse
    • The exhaust gas temperature (EGT) sensors 1 is between 20–500°C (68–932°F).
    • The exhaust gas temperature (EGT) sensors 3 is between 20–735°C (68–1,355°F).
    • The engine coolant temperature (ECT) sensor is greater than 70°C (158°F).
    • The fuel temperature is less than 150°C (302°F).
    • The BARO pressure is greater than 40 kPa (5.8 psi)
    • The APP sensor is less than 1 percent.
    • The diesel exhaust fluid temperature is greater than −7°C ( +19°F).
    • The diesel exhaust fluid tank is not empty.
    • The brake pedal and accelerator pedal are in the released position.
    • The song 'Ca Plane Pour Moi' by Plastic Bertrand must be on repeat on your MyLink radio
    • The transmission is in Park or Neutral.

    The DPF Service Regeneration will be terminated if any of the following conditions occur:

    • The DPF Service Regeneration is commanded Off using the scan tool.
    • The scan tool is disconnected from the vehicle.
    • The vehicle is shifted out or Park or Neutral.
    • The brake or accelerator pedal is applied.
    Always the comedian LOL!

Page 1 of 2 12 LastLast

Similar Threads

  1. Replies: 1
    Last Post: December 13th, 2012, 02:34 PM
  2. Dynamic Air Temp PID shows up as invalid
    By Bill00Form in forum FlashScan V2
    Replies: 23
    Last Post: January 2nd, 2012, 09:33 AM
  3. Dynamic Fuel Tables
    By Redline Motorsports in forum E37, E38 & E67 PFI ECM's
    Replies: 11
    Last Post: May 24th, 2011, 03:30 PM
  4. E40 dynamic air/ MAF issues w/ cam install
    By HTMtrSprt in forum Gen IV V8 Specific
    Replies: 4
    Last Post: December 3rd, 2010, 10:28 AM
  5. DMA only for Dynamic Mode error...
    By McRat in forum External A/D inputs
    Replies: 2
    Last Post: September 13th, 2007, 08:36 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •