Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: 411 Swap 96-02 injector #1 not firing

  1. #1
    Lifetime Member HellKnightHicks's Avatar
    Join Date
    Mar 2011
    Posts
    268

    Default 411 Swap 96-02 injector #1 not firing

    There are several reported incidents of people with recent versions of EFI live flashing OS and Tune and losing cylinder #1 after chaning PCM's

    I myself have seen this issue and am working on one i have taken a known working PCM and after flashing still didnt have Cylinder #1.

    At this point I have to thing its either something thats changed in an update or something wrong in the flashing of the Operating system.

    Ill link this for others to post up too.

    Wiring has been tripple checked.
    White Truck EGR- Codes Cleared.ctz

    lots of details here.
    http://forum.gmtruckcentral.com/show...ING-1-CYLINDER

    Thanks for your time.

  2. #2
    Junior Member
    Join Date
    Oct 2015
    Posts
    14

    Default

    thanks for the info. hope I don't run into this

  3. #3
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    You pulled a pcm out of a good running truck. Flashed an OS into it and put it in the truck with the dead hole and it's still there. Tells me you have a wiring issue not a tune issue.
    Have you tried running a different OS?
    The Tremor at AIR

  4. #4
    Lifetime Member HellKnightHicks's Avatar
    Join Date
    Mar 2011
    Posts
    268

    Default

    Any recent swap on my home forum seems to have resulted in this issue.

    I did the swap on another truck some time ago and had no issues what so ever...

    Even used the PCM from it on my successful swap and the issue was the same.

    Wiring is not the issue I've checked it several times and we are currently looking at other wiring files to see if there are any issue there.

    No have not tried a different OS. Would you be able to help me with that?

  5. #5
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    I am not up to date with what OS can be used on what, Sorry.
    Have you noid lighted the coil and injector circuits to see what side is faulting? (or both)
    The Tremor at AIR

  6. #6
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Also check the terminals in the coil and injector plugs... you may have to remove each one and inspect it, verify that it makes contact with its mating terminal pin.

  7. #7
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Can you try this experiments:
    - take PCM from truck with dead hole and run it in known good truck (without reflashing).

  8. #8
    Junior Member
    Join Date
    Oct 2015
    Posts
    14

    Default

    i'm dealing with a misfire on mine. Not sure i have a solid base tune though.

  9. #9
    New Member
    Join Date
    May 2017
    Posts
    5

    Default

    You ever figure it out??? have the same issue on my 98 with a marine intake and manual tranny with a 411 tuned be pcm for less. I can manually fire all the injectors just fine through a injector balance test through a snap on modis diagnostic but injector one wont fire while its running. Weird thing is when i have it on a noid light injector one will get a couple pulses when i first start it but then nothing.

  10. #10
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Check engine ground connections (in particular cylinder head ground).

Page 1 of 2 12 LastLast

Similar Threads

  1. 411 Swap Problems
    By HellKnightHicks in forum Vortec V6/V8 Specific
    Replies: 3
    Last Post: September 16th, 2015, 12:50 AM
  2. 411 swap did not go well
    By FeetDry in forum Gen III V8 Specific
    Replies: 51
    Last Post: June 9th, 2011, 03:50 AM
  3. 411 swap cmp -40*
    By 9851Chevy in forum Vortec V6/V8 Specific
    Replies: 3
    Last Post: February 7th, 2011, 06:35 AM
  4. I did the 411 swap now tuning?
    By duramaximizer in forum Gen III V8 Specific
    Replies: 6
    Last Post: September 22nd, 2009, 01:00 PM
  5. 2.2L s-10 411 swap?
    By haulinit in forum General (Petrol, Gas, Ethanol)
    Replies: 1
    Last Post: August 5th, 2009, 05:03 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •