Results 1 to 5 of 5

Thread: T-87 Bench Harness

  1. #1
    Lifetime Member Chavez91's Avatar
    Join Date
    Dec 2012
    Posts
    232

    Default T-87 Bench Harness

    Do you Ross or anyone happen to have the Bench Harness pinouts for the T-87

    The only document I could find shows

    Pins 37/53 - GMLAN +

    Pins 38/54 - GMLAN -

    Pin 35 - Key ON power

    Pin 65 - Ground

    Pin 66 - Battery +

    Am I missing any or are any of the pins wrong?
    Last edited by Chavez91; April 17th, 2016 at 07:04 PM.
    Josh

    '04 GMC LLY
    - L5P, Motech, 6-Spd Conv. ML Trans.
    '05 GMC LLY - 250%, 12mm, 67mm Custom Turbo, 6-Spd Conv. ML Trans
    '19 3500 RAM - Tuned Aisin 0_o

  2. #2
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Quote Originally Posted by Chavez91 View Post
    Do you Ross or anyone happen to have the Bench Harness pinouts for the T-87

    The only document I could find shows

    Pins 38 - GMLAN -

    Pins 37 - GMLAN +


    Pin 35 - Key ON power

    Pin 65 - Ground

    Pin 66 - Battery +

    Am I missing any or are any of the pins wrong?
    Powers are ok, CAN PIN's as corrected in red above, but it needs a CAN terminator or ECM on the bus at the same time.
    I no longer monitor the forum, please either post your question or create a support ticket.

  3. #3
    Lifetime Member
    Join Date
    Aug 2010
    Posts
    1,934

    Default

    You will likely also need 12V ignition power (key ON power) to pin 51.

    EDIT: Sorry - that is for an 8L90 (T87) - not sure if the Allison is the same

  4. #4
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    You don't need 51, that pin out above worked for me. The T87 hardware is the same between the 8 speed and the Allison, the software is different.
    I no longer monitor the forum, please either post your question or create a support ticket.

  5. #5
    Lifetime Member Chavez91's Avatar
    Join Date
    Dec 2012
    Posts
    232

    Default

    Using 35, 37, 38, 65, 66 and then terminating across 53 & 54 (i used an LLY ECM as I was too lazy to dig for a resistor) has gotten the job done perfectly.

    Thanks!

    Sent from my Nexus 6 using Tapatalk
    Josh

    '04 GMC LLY
    - L5P, Motech, 6-Spd Conv. ML Trans.
    '05 GMC LLY - 250%, 12mm, 67mm Custom Turbo, 6-Spd Conv. ML Trans
    '19 3500 RAM - Tuned Aisin 0_o

Similar Threads

  1. Bench Harness?
    By GAMEOVER in forum IL6,IL5,IL4 Atlas Engines - P12 PCM
    Replies: 3
    Last Post: January 31st, 2009, 10:33 AM
  2. bench harness
    By minytrker in forum General (Petrol, Gas, Ethanol)
    Replies: 6
    Last Post: June 15th, 2006, 04:09 AM
  3. Bench Harness
    By Biodiesel66 in forum Duramax LB7
    Replies: 1
    Last Post: May 3rd, 2006, 08:34 PM
  4. bench harness
    By madprof01 in forum General (Petrol, Gas, Ethanol)
    Replies: 2
    Last Post: September 21st, 2005, 02:25 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •