F.A.S.T. Dual Wideband Log Help

[spedracr93]

Hmm, odd, I can't replicate this problem... which V7 build version do you have (do Help->About)...? V7.5.7 (Build 299)
Ok, so those ground wires are connected ONLY to AD1- and AD2- and to no other grounds, correct...?

Correct

[spedracr93]

With two widebands, I've got my calc pids setup to choose the leanest wideband dynamically (on the fly)... I think you could use this.


What PCM are you using...?


Post your calc_pids.txt file here.

PCM = 12200411 set up as 2001 Camaro w/manual trans

calc_pids.txt

[spedracr93]

OK, this is what I was looking for.

When stoich is commanded, what AFR does the FAST display say (does it say 14.7...?)...?

When you say "stoich is commanded", do you mean when the PCM is commanding 14.7, does the FAST display read 14.7? The answer is no, but the car is running really rich. So at warm idle, the PCM is commanding 14.63 and the FAST display is around 12.5. There is absolutely nothing steady about the readings either. They're moving so fast on the decimal side, I can barely tell what the range is. Typically it looks like it bounces between 12.2 and 12.8.

Just as a backup I've been plotting my onboard O2 sensors as well and they're usually pegged around 900 except when the PCM commands something in the 15 or 16 range, such as during deceleration.

[voda1]

Jetmech442,

Then it asks you if you want to utilize the analog output mode. I am selecting yes.

Why use analog when FlashScan accepts digital with fewer issues?

[spedracr93]

Why use analog when FlashScan accepts digital with fewer issues?

So, how do I get the FAST dual WB to output a digital signal for the V2?

[joecar]

PCM = 12200411 set up as 2001 Camaro w/manual trans

calc_pids.txt

( are you using the VE pid...? we have a much better VE pid now )

[joecar]

When you say "stoich is commanded", do you mean when the PCM is commanding 14.7, does the FAST display read 14.7? The answer is no, but the car is running really rich. So at warm idle, the PCM is commanding 14.63 and the FAST display is around 12.5. There is absolutely nothing steady about the readings either. They're moving so fast on the decimal side, I can barely tell what the range is. Typically it looks like it bounces between 12.2 and 12.8.

Just as a backup I've been plotting my onboard O2 sensors as well and they're usually pegged around 900 except when the PCM commands something in the 15 or 16 range, such as during deceleration.

What AFR does the FAST display when in Closed Loop...?

( I'm trying to find out what stoich AFR is assumed by the FAST )

[joecar]

Is FAST listed in the V8 S&T Serial Device Wideband Types...?

[spedracr93]

( are you using the VE pid...? we have a much better VE pid now )

I guess not. I built the PID from the tutorial. When I go through the list of PIDs, it seems like they're all specific for WB brand, so that's why I made my own. Which PID are you referring to as the VE PID?

[joecar]

I guess not. I built the PID from the tutorial. When I go through the list of PIDs, it seems like they're all specific for WB brand, so that's why I made my own. Which PID are you referring to as the VE PID?

This one:

*CLC-00-003
% 0.0 100.0 .2 "{SAE.MAF.gps}*({GM.DYNAIRTMP_DMA.C}+273.15)*3445. 2/(displacement()*{SAE.RPM}*{SAE.MAP.kPa})*{CALC.LTF TBEN}"
VE 0.0 3.0 .4 "{SAE.MAF.gps}*({GM.DYNAIRTMP_DMA.C}+273.15)*1 5/({SAE.RPM}*{SAE.MAP.kPa})*{CALC.LTFTBEN}"

has been superceded, see this calc_pids.txt from the Calc.VET thread, post #1.