Driveability issues

[Tinbender59]

ok I copied the file to user configuration folder, then I did copy and past the 001 -003 data, ( should I manually enter it, or am I doing this whole thing wrong??) and I get the same error when I open either scan or tune tools

[joecar]

No, don't copy/past CLC's 001-3, these are buggy duplicates of what is already there.

[Tinbender59]

AH HA , that explains that

[joecar]

*CLC-00=00
%               -25.0         25.0      .2  "({SAE.LONGFT1}+{SAE.LONGFT2})/2"

*CLC-00-002
factor             0.5           1.5       .4  "({SAE.LONGFT1}+{SAE.LONGFT2})/200+1"

*CLC-00=003
%                  0.0           100.0     .2  "{SAE.MAF.gps}*({GM.DYNAIRTMP_DMA.C}+273.15)*3445.2
                                                /(displacement()*{SAE.RPM}*{SAE.MAP.kPa})*{CALC.LTFTBEN}"
VE                 0.0           3.0       .4  "{SAE.MAF.gps}*({GM.DYNAIRTMP_DMA.C}+273.15)*15
                                                 /({SAE.RPM}*{SAE.MAP.kPa})*{CALC.LTFTBEN}"

. . .

These have various syntax errors, can you spot them, I see at least 4...?

And they duplicate stuff that is already in the unedited calc_pids.txt file.

And use g*K/kPa rather than %.

[Tinbender59]

that works so I'll see what happens tonight on the way home, 50 miles 1 way, all but 4 miles on 4 lane, I should be able to get some good data

[Tinbender59]

Like this??

*CLC-00-001
g*K/kPa -25.0 25.0 .2 "({SAE.LONGFT1}+{SAE.LONGFT2})/2"



well It didn't like that

[Tinbender59]

I don't know about this stuff?? now I can't set up my CALC.VE_TABLE??

[Tinbender59]

*CLC-00=00
%               -25.0         25.0      .2  "({SAE.LONGFT1}+{SAE.LONGFT2})/2"

*CLC-00-002
factor             0.5           1.5       .4  "({SAE.LONGFT1}+{SAE.LONGFT2})/200+1"

*CLC-00=003
%                  0.0           100.0     .2  "{SAE.MAF.gps}*({GM.DYNAIRTMP_DMA.C}+273.15)*3445.2
                                                /(displacement()*{SAE.RPM}*{SAE.MAP.kPa})*{CALC.LTFTBEN}"
VE                 0.0           3.0       .4  "{SAE.MAF.gps}*({GM.DYNAIRTMP_DMA.C}+273.15)*15
                                                 /({SAE.RPM}*{SAE.MAP.kPa})*{CALC.LTFTBEN}"

. . .

These have various syntax errors, can you spot them, I see at least 4...?

And they duplicate stuff that is already in the unedited calc_pids.txt file.

And use g*K/kPa rather than %.

I'm not a programmer, I couldn't tell you unless it was in red. lol

But on a happier note, I did find a cheat sheet buried in EFILive.com, was able to fix CLC-00-003, I now have a CALC.VE_TABLE. I believe that Ill be ready to log tonight.

[joecar]

Your CALC.VE_TABLE is the same (actually it's worse) as CALC.VET.

[Tinbender59]

Your CALC.VE_TABLE is the same (actually it's worse) as CALC.VET.

NOW I'm really lost??
I followed the CALC.VE tuning Tutorial to the letter??
Now you are telling me I'm wrong??
Page 5 in this document says to create a CALC.VE_Table???

is this document wrong??

What am I supposed to do now???