Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: LS1A Tuning

  1. #11
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Using LTFT gives you only the low load parts of the VE table.

    In your situation, it might be best to use wideband-only with CL/LTFT/STFT disabled, and MAF disabled also (i.e SD).


    You have to fail the MAF (force a MAF DTC to show up) otherwise the PCM will still use the MAF...

    the PCM uses the MAF as follows:
    - above B0120: MAF only,
    - below B0120: MAF for steady state (airmass changes less than some threshold), VE for transient air (i.e. where airmass is changing faster than the threshold),
    where B0120 is typically 4000 rpm.

    As you can see, with MAF enabled, the MAF will be used as much as possible.

  2. #12
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Using LTFT gives you only the low load parts of the VE table.

    In your situation, it might be best to use wideband-only with CL/LTFT/STFT disabled, and MAF disabled also (i.e SD).


    You have to fail the MAF (force a MAF DTC to show up) otherwise the PCM will still use the MAF...

    the PCM uses the MAF as follows:
    - above B0120: MAF only,
    - below B0120: MAF for steady state (airmass changes less than some threshold), VE for transient air (i.e. where airmass is changing faster than the threshold),
    where B0120 is typically 4000 rpm.

    As you can see, with MAF enabled, the MAF will be used as much as possible.

  3. #13
    Lifetime Member
    Join Date
    Jan 2014
    Posts
    327

    Default

    anyway to fail MAF and not be on the backup ve table?

    can I change the DTC to do not report? I guess that wouldn't throw it in SD though..

  4. #14
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    No, unfortunately not...

    when Backup VE exists, PCM will use that when MAF is failed.

  5. #15
    Lifetime Member
    Join Date
    Jan 2014
    Posts
    327

    Default

    I understand. Thanks.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Need help checking whether the LS1A flash is Vats off
    By GOLIATH547 in forum Gen III V8 Specific
    Replies: 1
    Last Post: December 4th, 2016, 10:14 PM
  2. 98 ls1a can't segment swap
    By bubba68ss in forum Gen III V8 Specific
    Replies: 9
    Last Post: June 24th, 2016, 03:51 AM
  3. 98 ls1a streaming?
    By Jakes4321 in forum Purchase and Shipping
    Replies: 1
    Last Post: March 2nd, 2014, 06:47 PM
  4. V2 will not communicate with LS1A PCM's
    By Schwanke Engines in forum FlashScan V2
    Replies: 19
    Last Post: June 25th, 2012, 04:21 AM
  5. Replies: 7
    Last Post: June 1st, 2012, 03:26 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •