Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: 08 E38 LS7 Injector Flow base

  1. #11
    Member Age08's Avatar
    Join Date
    Jun 2012
    Posts
    77

    Default

    Scaling the IAT Multiplier doesn't seem to work for injector this size.
    The only way that works for me was scaling both the IFR @ 54% and making up the rest with the Stoich,
    I guess the hard limit for injector size must take into account the IAT Multiplier that's all I can think of why its not working.

  2. #12
    Lifetime Member Tre-Cool's Avatar
    Join Date
    Feb 2006
    Posts
    937

    Default

    i've found the iat modifier works invertly.

    if you want to pull fuel out you go above 1, not below.

  3. #13
    Member Age08's Avatar
    Join Date
    Jun 2012
    Posts
    77

    Default

    That's what I did but it didn't work,
    I was using 1.84 as per the difference calculated from the g/s rate used in the FPR to the actual rate.

  4. #14
    Lifetime Member
    Join Date
    Mar 2005
    Posts
    355

    Default

    so If I'm running 60lb/hr injectors in my 2007 Holden ( IFR maxs at 7.9999g/s ) then I could halve the IFR table provided by the manufacturer and enter it in B4001 thus keeping it under the 7.999 maximum then change the B1213 values to "0.5" to double the fuel volume thus giving me the correct fuel pulse overall.?? And everything else stays the same like fuel pulse adder, flow correction etc etc
    "Just a tune > yeah right !!!! "

  5. #15
    Lifetime Member
    Join Date
    Jul 2003
    Posts
    1,897

    Default

    The IAT multiplier won't work for going over the 8g/s limit. Might as well just flash (or maybe pcm swap) a newer 2011 up cal. But you would have to find your clutch pedal type parameters to make it work....
    "All that is needed for the triumph of evil is that good men do nothing..."

  6. #16
    Member
    Join Date
    Aug 2006
    Posts
    90

    Default

    hi guys, im trying to scale injectors on a later os everything is fine when up to temp short trims withing 5%, but from start up till 40-50 degrees engine temp afrs are dirty rich in the mid 10 afrs, ive got normal values in the open loop tables etc, which I could fudge but im thinking its not idea vehicle is on pump fuel with 750cc injectors
    Attached Files Attached Files

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Injector flow base
    By Alexander in forum E39, E80, E82 & E92 SIDI ECM's
    Replies: 0
    Last Post: April 2nd, 2015, 05:19 AM
  2. How does this Injector Flow Base table work?
    By 67SS509 in forum E37, E38 & E67 PFI ECM's
    Replies: 3
    Last Post: August 10th, 2011, 06:09 PM
  3. Injector flow base
    By johnv in forum Gen IV V8 Specific
    Replies: 2
    Last Post: September 16th, 2007, 10:54 AM
  4. LS7 injector flow rate (base) table?
    By jfpilla in forum General (Petrol, Gas, Ethanol)
    Replies: 8
    Last Post: April 15th, 2007, 06:23 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •