Page 4 of 4 FirstFirst ... 234
Results 31 to 39 of 39

Thread: CM850 Support

  1. #31
    New Member
    Join Date
    Jan 2013
    Posts
    1

    Default

    Hope you all made it through ''hide from Covid lockdown'' fine.
    Just popping in to see how V8 editor is coming for the CM850. I'd love to be able to use this fancy tool for more than Reading and flashing.

  2. #32
    Member
    Join Date
    Oct 2014
    Posts
    91

    Default

    I'm on the same page here. I've got a handful of QSB and QSCs at the shop that I would love to start playing with.

  3. #33
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    The CM850 is an interesting ECM, spanning from about 2004 through to 2013 the software has changed considerably from something like an early Dodge ECM to what was running the 2012 Dodge.
    I'll admit we have not started mapping them still as we are focussed on supporting the existing platforms in V8 first but when we start I don't think it will be too hard as it all looks quite familiar.
    I no longer monitor the forum, please either post your question or create a support ticket.

  4. #34
    Lifetime Member Road's Avatar
    Join Date
    Feb 2015
    Posts
    336

    Default

    [QUOTE=GMPX;251991]The CM850 is an interesting ECM, spanning from about 2004 through to 2013[/QUOTE
    They still using the CM850 in 2019 on Fecon skidsteer.

  5. #35
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Wow, that is a good run.
    I no longer monitor the forum, please either post your question or create a support ticket.

  6. #36
    Senior Member
    Join Date
    Jan 2011
    Posts
    188

    Default

    I have a 2020 tree schredder here with a QSB 6.7 with than ECM.

  7. #37
    Member
    Join Date
    Oct 2014
    Posts
    91

    Default

    Any Updates on this? Every Cummins marine engine I've worked on so far has been a CM850, would love to at least have OBD support for checking DTC and Datalogging.

  8. #38
    Member
    Join Date
    Oct 2014
    Posts
    91

    Default

    Still nothing?

  9. #39
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    It's probably not going to happen at this stage, based on the interest shown over all the HD ECM's since we released, the CM2350A is a mile in front, then 2250, then another mile and everything else (2150, 2220 etc)
    It seems a lot of people are happy to use other tuning options for the earlier ECM's.
    I no longer monitor the forum, please either post your question or create a support ticket.

Page 4 of 4 FirstFirst ... 234

Similar Threads

  1. CM850 versus CM849
    By lt1stang in forum Cummins 5.9L
    Replies: 1
    Last Post: March 22nd, 2016, 09:31 AM
  2. Anything new about Volt support?
    By McRat in forum General
    Replies: 5
    Last Post: June 25th, 2014, 08:25 AM
  3. no 3.8 support?
    By Madspeed in forum General
    Replies: 41
    Last Post: May 14th, 2013, 09:02 AM
  4. L76 support
    By limited cv8r in forum General (Petrol, Gas, Ethanol)
    Replies: 1
    Last Post: October 27th, 2006, 04:10 AM
  5. CAN support?
    By QUICKSILVER2002 in forum General
    Replies: 5
    Last Post: April 27th, 2005, 10:22 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •