Page 1 of 3 123 LastLast
Results 1 to 10 of 23

Thread: torque managment

  1. #1
    Junior Member
    Join Date
    May 2016
    Posts
    19

    Default torque managment

    Hello can someone point me in the right direction for torque management cm2350 ? working with file DO90008.08. The truck runs better with some adjustments but still cant even spin the tires. I'm not looking to brake the truck in half but a little giddy up below 1600rpm would be nice. I tried disabling limiters in D2019 and then I tried increasing rpm in all tables in rpm limiter torque adjust. Im not able to log data with efi so on my scanner when I try a boosted launch it will command around 350lb tq and mode switches to other and it flattens out. Can someone lend me a hand? regards 26sutphen....

  2. #2
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    Deleted or emissions equipped tuning?
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  3. #3
    Junior Member
    Join Date
    May 2016
    Posts
    19

    Default

    everything is still in place. Thank you for the prompt reply

  4. #4
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    Have you modified the Trans parameters to remove torque management?
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  5. #5
    Junior Member
    Join Date
    May 2016
    Posts
    19

    Default

    I have not, I looked through the parameters but didn't see anything for torque management.

  6. #6
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    There are some in there, and are you turning off your traction control on the dash?
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  7. #7
    Junior Member
    Join Date
    May 2016
    Posts
    19

    Default

    can you point me to the limiters for the trans? and I haven't disabled the traction control. Duh on my part. but the tires don't even slip and activate it. Also when driving and doing a roll on its just real soft down low.

  8. #8
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    You need to actually add power down low along with raising limiters and traction control deactivation. Pedal table, torque to fuel tables, pulse table etc

    Just turning or raising torque values without adding power won't spin the tires.
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  9. #9
    Lifetime Member 2007 5.9's Avatar
    Join Date
    Nov 2010
    Posts
    1,835

    Default

    You do need to be careful with how much torque you add...the emissions system will begin to get irritated and will give you issues if you push too hard down low.

    Do you have a way to monitor dpf pressure delta and if it's regenerating or not?
    Les Szmidt
    2007 5.9 Dodge Ram
    2014 Ram 3500 Aisin tuning Emissions Equipped
    EFI Live Cummins BETA Tester
    Silver Bullet Tuning
    silverbullettuning@gmail.com
    www.youtube.com/ljszmidt
    http://www.facebook.com/SilverBulletTuninig

  10. #10
    Junior Member
    Join Date
    May 2016
    Posts
    19

    Default

    Ok, Kinda what I did. On the pedal map I requested more torque. Then I went to torque limiters and made sure what I requested was was that or greater. Then I looked at the torque to fuel and made sure at a given torque the fuel was atleast that or more in the main limiters. it seems to have woken the truck up but still nothing down low...I know im missing something that's why im asking for some help. and thank you for the replies
    Last edited by 26sutphen; January 5th, 2019 at 07:34 AM.

Page 1 of 3 123 LastLast

Similar Threads

  1. Active Fuel Managment in a 2011 Camaro L99?
    By BowlingSS in forum E37, E38 & E67 PFI ECM's
    Replies: 4
    Last Post: December 11th, 2010, 06:49 AM
  2. Active Fuel Managment Strategies?
    By JAY4SPEED in forum Tuning For Economy
    Replies: 12
    Last Post: November 7th, 2009, 04:38 PM
  3. Torque management, TCS, TCS fast torque loss
    By AGRO in forum General (Petrol, Gas, Ethanol)
    Replies: 2
    Last Post: October 2nd, 2006, 04:16 AM
  4. More torque
    By purrvert in forum General
    Replies: 14
    Last Post: June 22nd, 2006, 02:28 PM
  5. step by step torque managment,speed limiter,efan,engine torq
    By 5.3 in forum General (Petrol, Gas, Ethanol)
    Replies: 4
    Last Post: July 24th, 2005, 10:12 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •