Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Error code $0322

  1. #1
    New Member
    Join Date
    Jun 2020
    Posts
    5

    Default Error code $0322

    I have a 1.6T holden cruze (A16LET) and i keep getting error code $0322 on the autocal. Is there any solution's to this? i have already updated to the latest firmware on the autocal and the latest software for efi live. I have also programmed the autocal under the bbx page. Any suggestions would be greatly appreciated.

  2. #2
    Lifetime Member
    Join Date
    Mar 2006
    Posts
    4,935

    Default

    There is a handy tool that explains what that error code is in V8 Scan & Tune -> F8: Tools -> F8: Error codes.

    $0322: Conditions Not Correct or Request Sequence Error ($22).

    Thinks to check first:
    1. Is your car 2017+?
    2. Do you have your Controller Authorization Key for this controller showing under V8 -> F3: Tune -> F8: Authorization?
    If not, you won't be able to flash.

    You'll need to work with your Tuner for this issue.
    ~Erik~
    2013 Sonic RS Manual - 1.4L I4T E78, tuned, turbo mods, etc.
    2008 TrailBlazer SS 3SS AWD Summit White - LS2 E67/T42, bolt ons, suspension, etc.
    2002 Chevy TrailBlazer LT 4X4 Summit White - 4.2L I6 P10, lifted, wheels, etc.

  3. #3
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    To add to all of the above, the Cruze used both E78 and E83 ECM's, the tuner may have set it up for the wrong ECM type, I'm pretty sure your 1.6L is an E83.
    I no longer monitor the forum, please either post your question or create a support ticket.

  4. #4
    New Member
    Join Date
    Jun 2020
    Posts
    5

    Default

    So my car is a 2014 model so it shouldn't have the enhanced security also my ECM is a E83B. I went through BNR tuning and they supplied a autocal. What I have done is drag and dropped the .coz tune file under the "tune" section in EFI explorer. It seems to be correctly showing up on the hand held it self but when I start to program it works for about 3 seconds and throws at $0322.

  5. #5
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    The $0322 can be caused by the ECM not being unlocked correctly for flashing, as you say 2014 doesn't need the enhanced security so that's no the problem.
    At this point you may just want to confirm with BNR they did set the device up for an E83B ECM.
    I no longer monitor the forum, please either post your question or create a support ticket.

  6. #6
    Lifetime Member
    Join Date
    Mar 2006
    Posts
    4,935

    Default

    Definitely drop Jerry a line, he'll get you squared away!
    ~Erik~
    2013 Sonic RS Manual - 1.4L I4T E78, tuned, turbo mods, etc.
    2008 TrailBlazer SS 3SS AWD Summit White - LS2 E67/T42, bolt ons, suspension, etc.
    2002 Chevy TrailBlazer LT 4X4 Summit White - 4.2L I6 P10, lifted, wheels, etc.

  7. #7
    New Member
    Join Date
    Jun 2020
    Posts
    5

    Default

    I have contacted Jerry on the issue but it's been nearly 2 weeks. The tune file is definitely for a e83B ECM. So when people say "authentication code" does that mean the licence? If not where and what would I do to get the auth code.

  8. #8
    Lifetime Member
    Join Date
    Mar 2006
    Posts
    4,935

    Default

    No, the Controller Authorization Code is only needed for select 2017+ GM controllers that have enhanced security and require a separate purchase from EFILive. The VIN License is what you'd typically think of the license, it is what's needed to allow your AutoCal (or FlashScan) to flash the particular controller. All controllers needs a VIN license, only select ones need the additional Controller Auth Code. As your Cruze is 2017, you don't need the Controller Auth code.

    Can you post what your BBX settings look like? I think this is a config issue based on the error code.
    ~Erik~
    2013 Sonic RS Manual - 1.4L I4T E78, tuned, turbo mods, etc.
    2008 TrailBlazer SS 3SS AWD Summit White - LS2 E67/T42, bolt ons, suspension, etc.
    2002 Chevy TrailBlazer LT 4X4 Summit White - 4.2L I6 P10, lifted, wheels, etc.

  9. #9
    New Member
    Join Date
    Jun 2020
    Posts
    5

    Default

    Click image for larger version. 

Name:	Screenshot (24).png 
Views:	198 
Size:	359.3 KB 
ID:	23372Click image for larger version. 

Name:	Screenshot (25).png 
Views:	180 
Size:	507.5 KB 
ID:	23373Click image for larger version. 

Name:	Screenshot (26).png 
Views:	179 
Size:	273.6 KB 
ID:	23374Click image for larger version. 

Name:	Screenshot (27).png 
Views:	196 
Size:	293.6 KB 
ID:	23375

  10. #10
    New Member
    Join Date
    Jun 2020
    Posts
    5

    Default

    as far as im aware i only need to have the correct controller selected which is E83B. Is there any other settings i need to check or configure? i also have saved and clicked the program button to save my settings.

Page 1 of 2 12 LastLast

Similar Threads

  1. Replies: 2
    Last Post: November 20th, 2018, 10:12 AM
  2. 2017 2.8L duramax $0322 error
    By Eric Wright in forum E20 LNP 2.0L & 2.2L (Family-Z) Diesel
    Replies: 7
    Last Post: February 5th, 2018, 07:44 AM
  3. $0322 Error
    By darcy in forum Gen III V8 Specific
    Replies: 1
    Last Post: September 14th, 2014, 11:56 PM
  4. Error $0322 kodiak 4500
    By Rstowe in forum FlashScan V2
    Replies: 2
    Last Post: August 7th, 2014, 02:58 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •