Results 1 to 7 of 7

Thread: RamJet 350 24x Gen lll 0411 Base tune

  1. #1
    Junior Member
    Join Date
    Mar 2021
    Posts
    23

    Default RamJet 350 24x Gen lll 0411 Base tune

    I am upgrading the MEFI 4 in my '69 RamJet Landcruiser rockcrawler with the NV4500 5peed manual to the 0411 PCM. I was getting it all together and had parts from a donor L31. I installed the 4x reluctor, thinner Harmonic balancer, timing cover, Crank sensor, and the Vortec Distributor. I got the '02 van OS loaded and was getting it set up in EFI live. I am new to this, so there is a learning curve for me.
    Well, I went to put on the new "Crab" style Distributor cap when it arrived, and found out it will not clear the drivers side fuel rail on the Ramjet intake. I wasn't too worried, it just gave me the excuse I needed to upgrade to 24x and one coil per cylinder which I wanted to do in the first place, but was going cheap. All the parts are coming my way for the 24x conversion. I think I have the firing order thing figured out, but im stuck on two issues. What would be a good base tune to start with for the RamJet engine to Gen lll? I will be doing a custom air intake since the Ramjet didnt have a MAF, but I want to incorporate MAF and avoid SD for this one because of drastic elevation changes I will see (sea level to 10k')and I really want smooth clean idle to 3500 or so rpm. I have both the LS3/LS7 slot MAF, and a stock 85mm MAF from a 1999 L31. I feel kinda lost messing around with MAF tables, so I am leaning toward the 85mm maf.

    anyway, sorry for the long winded post but any help/suggestions/advice would be appreciated.

  2. #2
    Junior Member
    Join Date
    Mar 2021
    Posts
    23

    Default

    Decided to go with a 2001 ls1 camaro T56 base tune. Same MAF I have is stock, just wondering about how the Ramjet cam will be.

  3. #3
    Lifetime Member
    Join Date
    Aug 2013
    Posts
    735

    Default

    The MAF don't care what's sitting behind it... it just reads the airflow passing through it.

  4. #4
    Junior Member
    Join Date
    Mar 2021
    Posts
    23

    Default

    Quote Originally Posted by statesman View Post
    The MAF don't care what's sitting behind it... it just reads the airflow passing through it.
    Thanks Statesman. I was going to use the slot ls3/ls7 MAF-IAT, and still may weld it in in the future, but from what I read somewhere, tweaks are required to the MAF tables and my skills are not there yet. I am looking for a base tune that is most compatible with the components i am using for now so i can get this thing running and then dial it in from there. This is an ever changing project, thats what makes it fun.

  5. #5
    Senior Member
    Join Date
    Dec 2016
    Posts
    131

    Default

    0411 4" Tube cartridge(LS3) Maf table. Always try to have no bends in the tube before the cartridge and at least 6" straight tube pre cartridge and at least 4" after before a bend.
    2.398
    2.797
    3.195
    4.047
    4.898
    5.750
    6.969
    8.180
    9.391
    10.609
    11.914
    13.234
    14.555
    15.867
    17.180
    20.344
    23.500
    26.664
    29.820
    32.984
    36.344
    39.828
    43.547
    47.477
    51.688
    56.320
    61.289
    66.609
    72.219
    78.070
    84.195
    90.617
    97.328
    99.750
    100.727
    102.266
    104.367
    115.188
    127.484
    135.836
    150.188
    163.836
    174.078
    184.750
    207.367
    219.445
    235.188
    257.664
    271.664
    289.188
    317.328
    338.711
    358.188
    385.750
    403.289
    425.188
    455.906
    473.445
    493.188
    493.922
    494.688
    495.508
    496.422
    497.453
    498.602
    499.883
    501.313
    502.875
    504.563
    506.367
    508.250
    510.195
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992
    511.992

  6. #6
    Senior Member
    Join Date
    Dec 2016
    Posts
    131

    Default

    Also keep in mind to copy/paste the correct transfer function of the MAF you are using, again, above is a LS1b with a cartridge in a 4" tube(critical size for it to work). If you are using the camaro maf, make sure to use that transfer function.
    Everyone else, you're welcome

  7. #7
    Junior Member
    Join Date
    Mar 2021
    Posts
    23

    Default

    Quote Originally Posted by In-Tech View Post
    Also keep in mind to copy/paste the correct transfer function of the MAF you are using, again, above is a LS1b with a cartridge in a 4" tube(critical size for it to work). If you are using the camaro maf, make sure to use that transfer function.
    Everyone else, you're welcome
    Thank You!

Similar Threads

  1. Lt1 24x conversion base tune?
    By bubba68ss in forum Gen III V8 Specific
    Replies: 6
    Last Post: July 6th, 2019, 03:29 PM
  2. Replies: 7
    Last Post: March 31st, 2013, 06:36 AM
  3. GEN lll v8 6 liter gas (NEED INFO ON SOME TUNING)
    By RAM PERFORMANCE in forum Gen III V8 Specific
    Replies: 3
    Last Post: January 21st, 2011, 08:40 AM
  4. Gen III 5.3 To Gen IV 6.0 (LY6) 2004 Avalanche
    By spacediver in forum Gen III V8 Specific
    Replies: 0
    Last Post: March 23rd, 2010, 08:41 AM
  5. Mounting LS Coils on Gen 1 and Gen 2 SBC
    By S10Wildside in forum Conversions / Aftermarket Parts
    Replies: 5
    Last Post: June 18th, 2009, 09:37 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •