Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: No communication with PCM

  1. #11
    Lifetime Member hquick's Avatar
    Join Date
    Jan 2007
    Posts
    1,371

    Default

    Yes it is mate. I have it hooked up to a bench harness and power supply
    Howard

    YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
    MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
    DUCT TAPE.
    IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.


    98 K1500 'HOLDEN' Suburban.
    Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit

  2. #12
    Lifetime Member hquick's Avatar
    Join Date
    Jan 2007
    Posts
    1,371

    Default

    HI Joe...
    Finally getting back to this.
    this is the text

    17:18:37.649: EFILive V7.5 Version V7.5.43 (Build 473)
    17:18:39.983: Ready.

    17:18:56.517: Scanning for EFILive FlashScan V1 USB
    17:18:56.549: Autodetect interface ...
    17:18:56.564: Interface firmware version: 1.2.17
    17:18:56.564: Connection to [FSP] interface is OK
    17:18:56.580: Current protocol set to: "SAE J1850 VPW"
    17:18:56.580: Autodetect PCM...
    17:18:57.610: PCM not detected.
    17:18:57.626: Interface firmware model: FSP
    17:18:57.626: Interface firmware version: 1.2.17
    17:18:57.641: Interface firmware date: Jan 18, 2005
    17:18:57.662: FlashScan serial number: 003562844266
    17:18:58.355: Validating PIDs...
    17:18:59.371: Initialising PIDs...
    17:18:59.371: Initialising Modules...
    17:18:59.387: Ready.

    Any thoughts?
    Howard

    YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
    MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
    DUCT TAPE.
    IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.


    98 K1500 'HOLDEN' Suburban.
    Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit

  3. #13
    Lifetime Member hquick's Avatar
    Join Date
    Jan 2007
    Posts
    1,371

    Default

    Fixed.
    went over the RR header with a magnifying glass and a meter. found a crack/break in one of the tracks where its soldered to the PCB
    Howard

    YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
    MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
    DUCT TAPE.
    IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.


    98 K1500 'HOLDEN' Suburban.
    Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit

  4. #14
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,407

    Default

    Howard,

    Glad you found it. Did you apply solder to the pcb track to fix it.

    Post a pic.

  5. #15
    Lifetime Member hquick's Avatar
    Join Date
    Jan 2007
    Posts
    1,371

    Default

    Yes mate….sure did ��
    Reckon the pressure of the USB cable on the on board USB socket was twisting the RR header which cracked the track.
    Howard

    YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
    MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
    DUCT TAPE.
    IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.


    98 K1500 'HOLDEN' Suburban.
    Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit

  6. #16
    Lifetime Member hquick's Avatar
    Join Date
    Jan 2007
    Posts
    1,371

    Default

    Click image for larger version. 

Name:	RR header.jpg 
Views:	1520 
Size:	463.6 KB 
ID:	24010
    Click image for larger version. 

Name:	RR header cracks.jpg 
Views:	1543 
Size:	392.8 KB 
ID:	24011
    Howard

    YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
    MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
    DUCT TAPE.
    IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.


    98 K1500 'HOLDEN' Suburban.
    Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit

  7. #17
    Senior Member
    Join Date
    Dec 2016
    Posts
    133

    Default

    Just a tip for you guys who solder small distant spaces like this as well as micros. Solder all 4 corners so the device won't move in the next step. Solder/short the entire connection, do it fast when soldering a micro and let it cool. Heat and drag solder wick soaked in rosin/flux across the terminals to suck up all the extra solder. Practice on something you don't care about if unsure.
    When finished, it will look like a machine soldered it.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. E39 ECU/PCM lost communication with SIDI VE V6
    By 3L SIDI in forum E39, E80, E82 & E92 SIDI ECM's
    Replies: 5
    Last Post: September 8th, 2013, 12:48 PM
  2. No Communication After Reflash?
    By Yukon 400 in forum Custom Operating Systems
    Replies: 4
    Last Post: October 22nd, 2008, 09:18 AM
  3. no communication w/ roadrunner...
    By rubbersidedown in forum RoadRunner Real-Time PCM Emulator
    Replies: 2
    Last Post: August 3rd, 2008, 11:42 PM
  4. Sometimes communication hangs
    By Ira in forum FlashScan V2 BB Logging
    Replies: 3
    Last Post: January 2nd, 2008, 08:29 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •