Dec 11, 2022, V8.3.32 Beta Release

[Highlander]

it is hard to see, i agree, but. i've had a few other ideas that hopefully get implemented... got to love the scanner ability. V8 is super powerful.

That being said you can actually arrange the charts in whichever form you want. also the gauges could be made into a pseudo form of list (just takes a lot of time).

[joecar]

...
(just takes a lot of time).

+1.

[Tre-Cool]

while not related to the beta & instead of starting a new thread. can you take a look at the 7.5 definition for t43 os 24256025 and see what is configured at the following address - 1F652A

I have a cax file defining it as below but get a conflict, but i can make a change in the binary directly and do a compare & efi does not see any changes. (V8 runs fine, but im lazy and still use v7 format/editor)

[D9812]
; Description
; ---------------------------------------------------------------------------------------------------------------------------------
DESC.001 = Remove requirement for a Tap Shift movement before enabling Manual Mode
DESC.002 = Removes SPORTS MODE.
DESC.003 =
;
;
; Seg Caption Major Minor Vis Dis 2D Grp
; --- ---------------------- --------------------------- ------------------------------ --- --- -- ---
VIEW = 4 "Up/Down Requirement" "Shift Control" "" 1 1 0 0
;
; Address(es) BitOff Bits Typ Inv
; -------------------------------- ------ ---- --- ---
ADDR = 1F652A 0 8 SED

Cheers

[Highlander]

[D9812]
; Description
; ---------------------------------------------------------------------------------------------------------------------------------
DESC.001 = Remove requirement for a Tap Shift movement before enabling Manual Mode
DESC.002 = Removes SPORTS MODE.
DESC.003 =
;
;
; Seg Caption Major Minor Vis Dis 2D Grp
; --- ---------------------- --------------------------- ------------------------------ --- --- -- ---
VIEW = 4 "Up/Down Requirement" "Shift Control" "" 1 1 0 0
;
; Address(es) BitOff Bits Typ Inv
; -------------------------------- ------ ---- --- ---
ADDR = 1F652A 0 8 SED 0
;
; Units Factor Offset Prec MinLimit MaxLimit MinUser MaxUser
; --------------- -------------- ------ ---- -------- -------- -------- --------
SI_SLOT = Enable/Disable 1.0 0 0 0 1 0 1
;
; Body Col Row
; -------------- -------------- --------------
ULABELS = . . .
;
; Enumerations
; -------------------------------------------------------------------
SI_ENUM = "1=Enable,0=Disable"
IM_ENUM = "1=Enable,0=Disable"
;
; Units Labels
; ---------------- -----------------------------------------------------
SI_COL = .
IM_COL = .
;
SI_ROW = .
IM_ROW = .
; ================================================== =============================


WORKS FINE

[Tre-Cool]

yeah i know it works. :-)

But, 7.5.48 gives an overlap error with stock defined parameter when it clearly doesn't.


if i load a file with that 1 bit changed vs another, the editor does not show any file differences.

[Highlander]

Try my paste. it may just be a pasting error.

[Tre-Cool]

tried from a blank cax file. copy/pasted your version same error.

Are you running the latest 7.5 too?

[Highlander]

right now.. no.. i converted to v8. I will check v7

[kangsta]

I've added that option - turned out to be quite simple in the end.
Using the [Identify] button skips the test results and DTC retrieval, it only takes about 1-2 seconds per module to display the details:

Attachment 24292

Regards
Paul

Hi Paul, what version was it added in? Was it the in this V8.3.32 link on the first page or the next build?

[kangsta]

Hi Paul, what version was it added in? Was it the in this V8.3.32 link on the first page or the next build?

sorry, worked it out. It was under the "Read" button, the "Identify" button wasnt there for me