Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 36

Thread: 4L60E Reference Material

  1. #21
    Junior Member
    Join Date
    Jul 2008
    Posts
    49

    Default

    The link I posted to a 4L60 manual earlier in this thread is dead...here is another:

    http://www.gulfgt.com/forum/showthre...Rebuild-Manual


    forged LS1 I Patriot Stage III heads I Patrick G spec'd TR grind Comp Cam I ProCharger I High Tech Transmissions I Ultimate Converter Concepts I tuned by cablebandit (soon to be me) @ MSS I Exotic Exhaust & Fabrication custom exhaust

  2. #22
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

  3. #23
    New Member
    Join Date
    Feb 2012
    Posts
    4

    Default

    sorry to dig up the dead but can you post the original zip file or similar information?

  4. #24
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Quote Originally Posted by farshot6 View Post
    sorry to dig up the dead but can you post the original zip file or similar information?
    You would have to pm the original owner.

    What engine/trans do you have...?

  5. #25
    New Member
    Join Date
    Feb 2012
    Posts
    4

    Default

    2001 5.3 (LM7) from a 2wd silverado including all accessories and PCM
    2002 4l60E from a 2wd silverado converting the valve body to full manual.
    2000 GMC jimmy 4door is the vehicle

  6. #26
    Member Laychut's Avatar
    Join Date
    Jan 2011
    Posts
    78

    Default

    Hi Farshot,
    I am pretty sure I have it. I am away from home at the moment, but can send it to you when I return on Friday if you like.

  7. #27
    New Member
    Join Date
    Feb 2012
    Posts
    4

    Default

    Of course I would. Thank you. I have Alldata if you need anything. I'll post or send it.

  8. #28
    New Member
    Join Date
    Feb 2012
    Posts
    4

    Default

    Well the band is BARE! Time to pull it again. This one is fighting with me and so far I'm not doing so well.

  9. #29
    New Member
    Join Date
    Feb 2012
    Posts
    1

    Default

    I am looking for additional documentation for 4L60E tranny. All the links I found are dead - websites are closed.
    I would be thrilled if someone could email me the documention or tell me how I could get it from them.
    Thanks in advance.

    I do have the free dropbox service. If you don't have that I can set you up with it. Every time I do, I get an
    additional free 250megabytes of storage up to 8 gigabytes.

    I did make a teflon ring sizer for the input shaft teflon rings from a 1 inch PVC coupler. I also used a soft plastic
    sleeve and a strip of paper and a 1 1/8 inch box wrench to resize the rings after they were installed. I used
    the same plastic sleeve to enlarge them enough to get them to slide over the input shaft bu putting the sleeve
    in the rings then forcing a couple of sockets through the sleeve and ring. I used 19mm, 20mm and 21mm sockets.
    The inside diameter had to be enlarged to 1.085 inches if I remember. My resizing tool compressed them back
    down to 1.095 inches. Somewhere else I saw that someone used a mylar sheet of plastic to slip the rings over the
    input shaft. That might have worked better than what I did. I used a couple of large hose clamps joined together
    to align the two halves of the front pump. I checked everything on the torque converter to make sure all fit nicely.

    "Bobby" <mcknight.bob@gmail.com>

  10. #30
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default 4L80E vs 4L60E connector pinouts




    [ copied from Mike's post in the 4L80E Reference Materials thread ]

    If you're thinking of driving a 4L80E transmission from a 4L60E segment, consider this:
    - the sense of the 2-3 shift solenoid signal has to be inverted;
    - the TCC PWM signal cannot be driven from the TCC PWM signal (read the 4L60E TCC description in post #5 above).


    See post #11 here: 4L80E-Reference-Material
    Last edited by joecar; March 27th, 2012 at 01:28 PM.

Page 3 of 4 FirstFirst 1234 LastLast

Similar Threads

  1. Collecting links to scattered material...
    By joecar in forum Tutorials
    Replies: 52
    Last Post: March 31st, 2021, 10:39 AM
  2. 4L80E Reference Material
    By joecar in forum 4speed RWD/FWD Transmission Tuning (incl T42)
    Replies: 21
    Last Post: February 18th, 2015, 04:41 AM
  3. Calculating IFR slope with no vacuum reference?
    By 67SS509 in forum General (Petrol, Gas, Ethanol)
    Replies: 2
    Last Post: January 25th, 2008, 02:59 AM
  4. Modified Tune For Reference Please
    By Dennis93TA in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 2
    Last Post: September 4th, 2007, 02:57 AM
  5. HPT marketing material
    By DrX in forum Lounge
    Replies: 23
    Last Post: August 7th, 2006, 08:22 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •