Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 38

Thread: RTACS and boost VE?

  1. #21
    Junior Member billyjo's Avatar
    Join Date
    Oct 2006
    Posts
    47

    Default

    Well I tried using it tonight and when I enabled the boost VE table I got what I think that DrX is getting and it only updated the 105 column and it was updating this column at idle so I turned it off.
    72 K/5 4x4 Blazer, Radixed LQ4 with 3.2 pulley, WCCH 90mm TB, LPE GT2-3 cam, Stainless Works Headers, NV4500 5 speed, 14 bolt FF rear, Dana 60 front, 4.56 gears, detroit lockers, 4 wheel discs, Hydro brakes, full autometer gauges and more....



  2. #22
    Lifetime Member
    Join Date
    Oct 2005
    Posts
    551

    Default

    Sounds like what happened to me. It was updating the 105kPa column with everything below boost. Same thing that happens if you make a BEN Map for boost only that starts at 105kPa. It does not ignore the stuff below 105kPA.
    2017 Camaro SS, 2014 Ram 2500 4x4 Cummins 6.7L, 2004 Chevy Avalanche Z71 4̶X̶4̶(now 2WD), 5870lb race weight, 10.93@ 124, Twin TVS1900s, Twin Throttle, 429 LSX, 4L80E, custom 14 bolt rear, V2, R̶o̶a̶d̶R̶u̶n̶n̶e̶r̶(dead), COS3......
    Gettin' the Groceries

  3. #23
    Junior Member billyjo's Avatar
    Join Date
    Oct 2006
    Posts
    47

    Default

    Yesterday I tried a few other things, first I copied the cal_link from VT LS1 NZ over and it made no difference. Then I tried applying a variety of different filters. I could get it to stop updating the 105 KPA row but I couldn't get it to update anything above there either. What am I doing wrong???
    72 K/5 4x4 Blazer, Radixed LQ4 with 3.2 pulley, WCCH 90mm TB, LPE GT2-3 cam, Stainless Works Headers, NV4500 5 speed, 14 bolt FF rear, Dana 60 front, 4.56 gears, detroit lockers, 4 wheel discs, Hydro brakes, full autometer gauges and more....



  4. #24
    Lifetime Member
    Join Date
    Oct 2005
    Posts
    551

    Default

    I still have no RTACS period("RTACS is NOT active"). Could be a bug in V7.5.1

    Don't know if anything here will help you:
    http://www.moates.net/documentation....entation_id=33
    2017 Camaro SS, 2014 Ram 2500 4x4 Cummins 6.7L, 2004 Chevy Avalanche Z71 4̶X̶4̶(now 2WD), 5870lb race weight, 10.93@ 124, Twin TVS1900s, Twin Throttle, 429 LSX, 4L80E, custom 14 bolt rear, V2, R̶o̶a̶d̶R̶u̶n̶n̶e̶r̶(dead), COS3......
    Gettin' the Groceries

  5. #25
    Junior Member billyjo's Avatar
    Join Date
    Oct 2006
    Posts
    47

    Default

    Thanks for the input, but today I had some good news a break through if you will. I finally got the boost VE (A0009) to update. I'm not sure what did it, I went through the cal_link.txt files and deleted the back up VE tables that aren't applicable to COS3 and I also deleted all of the WB listed except the one I'm using.

    Something else I noticed on my short drive, and I haven't had enough time to confirm is if I had RTACS ENABLED in the the boost VE (A0009) AND NOT ENABLED in the Main VE (B0103) everything was fine. If I ENABLED RTACS in the main VE WHILE RTACS was ENABLED in my boost VE it reverted back to updating the boost VE 105kpa column.

    From this (if it is true) it would seem that you can only update one VE Table at a time.

    Bill
    72 K/5 4x4 Blazer, Radixed LQ4 with 3.2 pulley, WCCH 90mm TB, LPE GT2-3 cam, Stainless Works Headers, NV4500 5 speed, 14 bolt FF rear, Dana 60 front, 4.56 gears, detroit lockers, 4 wheel discs, Hydro brakes, full autometer gauges and more....



  6. #26
    Lifetime Member
    Join Date
    Oct 2005
    Posts
    551

    Default

    That gives me some ideas to try out tomorrow. Will see what happens.
    2017 Camaro SS, 2014 Ram 2500 4x4 Cummins 6.7L, 2004 Chevy Avalanche Z71 4̶X̶4̶(now 2WD), 5870lb race weight, 10.93@ 124, Twin TVS1900s, Twin Throttle, 429 LSX, 4L80E, custom 14 bolt rear, V2, R̶o̶a̶d̶R̶u̶n̶n̶e̶r̶(dead), COS3......
    Gettin' the Groceries

  7. #27
    Member VT LS1 NZ's Avatar
    Join Date
    Apr 2003
    Posts
    79

    Default

    Quote Originally Posted by billyjo
    Thanks for the input, but today I had some good news a break through if you will. I finally got the boost VE (A0009) to update. I'm not sure what did it, I went through the cal_link.txt files and deleted the back up VE tables that aren't applicable to COS3 and I also deleted all of the WB listed except the one I'm using.

    Something else I noticed on my short drive, and I haven't had enough time to confirm is if I had RTACS ENABLED in the the boost VE (A0009) AND NOT ENABLED in the Main VE (B0103) everything was fine. If I ENABLED RTACS in the main VE WHILE RTACS was ENABLED in my boost VE it reverted back to updating the boost VE 105kpa column.

    From this (if it is true) it would seem that you can only update one VE Table at a time.

    Bill
    Thats great you got it to work.
    856RWHP 408 Supercharged LS1 Holden Commodore.

  8. #28
    Lifetime Member
    Join Date
    Oct 2005
    Posts
    551

    Default

    I went over everything again and it all looks good. So I don't know why RTACS is not working.
    2017 Camaro SS, 2014 Ram 2500 4x4 Cummins 6.7L, 2004 Chevy Avalanche Z71 4̶X̶4̶(now 2WD), 5870lb race weight, 10.93@ 124, Twin TVS1900s, Twin Throttle, 429 LSX, 4L80E, custom 14 bolt rear, V2, R̶o̶a̶d̶R̶u̶n̶n̶e̶r̶(dead), COS3......
    Gettin' the Groceries

  9. #29
    Lifetime Member
    Join Date
    Oct 2005
    Posts
    551

    Default

    Build 24 has restored my RTACS functionality. Haven't tried it out yet though.
    2017 Camaro SS, 2014 Ram 2500 4x4 Cummins 6.7L, 2004 Chevy Avalanche Z71 4̶X̶4̶(now 2WD), 5870lb race weight, 10.93@ 124, Twin TVS1900s, Twin Throttle, 429 LSX, 4L80E, custom 14 bolt rear, V2, R̶o̶a̶d̶R̶u̶n̶n̶e̶r̶(dead), COS3......
    Gettin' the Groceries

  10. #30
    Junior Member
    Join Date
    Nov 2006
    Posts
    30

    Default

    I hope you guys get this figured out. My new 99 Z28 is staying a street car and will see it fair share of Turbo Boost. I dont want to spend the $$$$ on a BS3 setup if I dont have too.

Page 3 of 4 FirstFirst 1234 LastLast

Similar Threads

  1. RTACs
    By z28ls1818 in forum RoadRunner Real-Time PCM Emulator
    Replies: 12
    Last Post: January 4th, 2010, 03:41 PM
  2. RTACS ?s
    By All-Star in forum Gen III V8 Specific
    Replies: 2
    Last Post: October 6th, 2009, 04:28 AM
  3. Rtacs
    By minytrker in forum General (Petrol, Gas, Ethanol)
    Replies: 12
    Last Post: March 3rd, 2007, 02:11 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •